MJ Series
KEM-ML36100-08A
Safety and General Information
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general
safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control
your exposure and ensure compliance with the general population/
uncontrolled environment exposure limits, always adhere to the
following procedure:
•
Transmit no more than 50% of the time.
•
To receive calls, release the PTT button.
•
To transmit (talk), press the Push-to-Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting
(in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines:
• United States Federal Communications Commission, Code of
Federal Regulations; 47CFR part 2 sub-part J.
• American National Standards Institute (ANSI)/Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992.
• Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition.
• International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998.
• Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the
Frequency Range from 3 KHz to 300 GHz, 1999.
• Australian Communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
To ensure optimal radio performance and make sure human
exposure to radio frequency electromagnetic energy is within the
guidelines set forth in the above standards, always adhere to the
following procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could
damage the radio and may violate FCC regulations.
Do NOT hold the antenna when the radio is “IN USE.” Holding the
antenna affects its effective range.
Body-Worn Operation
To maintain compliances with RF exposure regulatory guidelines, if
you wear a radio on your body when transmitting always place the
radio in a Motorola-supplied or approved clip holder, holster, case
or body harness for this product. Use of non-Motorola-approved
accessories may exceed RF exposure regulatory guidelines.
If you do not use one of the Motorola-supplied or approved body-
worn accessories and are not using the radio held in the normal use
position,
ensure the radio and its antenna are at least 1 inch (2.5
cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or
without an accessory cable,
position the radio and its antenna at
least one inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories, visit our Web site at
www.motorola.com.
Electromagnetic Interference/Compatibility
Note:
Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic compatibility.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
IC Canada
The term "IC:" before the equipment certification number only
signifies that the Industry Canada technical specifications were met.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts,
turn off your radio in any facility where posted notices instruct you
to do so. Hospitals or health care facilities may be using equipment
that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard an
aircraft. Any use of a radio must be in accordance with applicable
regulations per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations
are consistent with the independent research by and
recommendations of the U.S. Food and Drug Administration.
People with pacemakers should:
• ALWAYS keep the radio more than 6 inches (15 cm) from their
pacemaker when the radio is turned ON.
• Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize the potential
for interference.
• Turn the radio OFF immediately if there is any reason to suspect
that interference is taking place.
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing aids.
In the event of such interference, you may want to consult your
hearing aid manufacturer to discuss alternatives.
Medical Devices – Other
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately
shielded from RF energy. Your physician may be able to assist you in
obtaining this information.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the
area where you drive, and always obey them. If you do use your
radio while driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if
driving conditions so require.
The use of a two-way radio while engaged in activities requiring
concentration may cause distraction or otherwise impair your
ability to safely participate in such activities. Always use technology
safely.
Do not place a portable radio in the area over an air bag or in the
air bag deployment area. Air bags inflate with great force. If a
portable radio is placed in the air bag deployment area and the air
bag inflates, the radio may be propelled with great force and cause
serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially
explosive atmosphere. Only radio types that are especially qualified
should be used in such areas as “Intrinsically Safe.” Do not remove,
install or charge batteries in such areas. Sparks in a potentially
explosive atmosphere can cause an explosion or fire resulting in
bodily injury or even death.
For More Information
For further information, you may contact Motorola as follows:
USA and Canada:
Call 1-800-638-5119, send e-mail to
[email protected] or visit www.motorola.com.
Mexico:
Call 01-800-021-0000.
Uruguay:
Call 00-04-01-78-70-11.
Panama:
Call 507-340-0293.
Note:
The areas with potentially explosive atmospheres referred to
above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
chemicals or particles (such as grain, dust or metal powders) and
any other area where you would normally be advised to turn off your
vehicle engine. Areas with potentially explosive atmospheres are
often—but not always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area,
or in areas posted “Turn off two-way radios.” Obey all signs and
instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna.
If a
damaged antenna comes into contact with your skin, a minor burn
can result.
Batteries
All batteries can cause property damage and/or bodily injury such as
burns if a conductive material—like jewelry, keys or beaded chains—
touch exposed terminals. The conductive material may complete an
electrical circuit (short circuit) and become quite hot. Exercise care in
handling any charged battery, particularly when placing it inside a
pocket, purse or other container with metal objects.
Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a
sharp blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the
plug will not fit the outlet, have the proper outlet installed by a
qualified electrician. An improper condition can result in a risk
of electric shock.
4. To reduce the risk of damage to the cord or plug, pull the plug
rather than the cord when disconnecting the charger from the
AC receptacle.
5. To reduce the risk of electric shock, unplug the charger from the
outlet before attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola
may result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on,
tripped over or subjected to damage or stress.
8. An extension cord should not be used unless absolutely
necessary. Use of an improper extension cord could result in a
risk of a fire and/or electric shock. If an extension cord must be
used, make sure that:
• The pins on the plug of the extension cord are the same
number, size and shape as those on the plug of the charger.
• The extension cord is properly wired and in good electrical
condition.
• The extension cord size is 18 AWG for lengths up to 100 feet,
and 16 AWG for lengths up to 150 feet.
9. The supply cord of the AC adaptor cannot be replaced. If the
cord is damaged, call customer service at the appropriate
number listed in the Warranty section.
Changes or modifications, not expressly approved by Motorola, may
void the user’s authority granted by the local regulatory agency to
operate this radio and should not be made. To comply with local
regulatory requirements, transmitter adjustments should be made
only by or under the supervision of a person certified as technically
qualified to perform transmitter maintenance and repairs in the
private land mobile and fixed services as certified by an organization
representative of the user of those services. Replacement of any
transmitter component (crystal, semiconductor, etc.) not authorized
by the local agency’s equipment authorization for this radio could
violate local government regulatory rules.
Note:
• Use of this outside the country where it was intended to be
distributed is subject to government regulations and may
be prohibited.
Licensing Information
Your Motorola radio has 22 operating channels. The FRS channels
operate within the range of free use frequencies and do not require
authorization from your local regulatory body.
The GMRS channels may require authorization from your local
regulatory body.
®
Display Screen Guide
Numbers for Channel,
Call Tone
Numbers for Codes
— Battery Meter
— Channel Power
Indicator (see Menu
Options)
— Lock
— Talk Confirmation
Tone (Roger Beep)
— Noise Filtering
— On/Off for each
feature
— Scan
— Call Tone,
Keypad Tone
— Weather Alert
— Hands-Free Use
Without
Accessories
— Hands-Free Use
With Accessories
MJ Series
Control Buttons
Volume
Push-to-Talk
Flashlight Button
Microphone
Call Tone
Scroll/Weather
Flashlight LED
Emergency Alert
LED Indicator
Accessory Jack
Menu/Lock
Scan/Monitor
Mini-USB
Charging Port
Getting Started
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or 3
AA alkaline batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover latch
up and remove the cover.
3. Remove the NiMH battery pack from the clear plastic bag.
(Do not disassemble or unwrap the battery pack.)
4. Insert the NiMH battery pack with the diagram facing you.
5. Reposition the battery cover and press down to secure.
Installing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover latch
up and remove the cover.
3. Insert the three AA alkaline batteries with + and - polarity as
shown inside.
4. Reposition the battery cover and press down to secure.
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
to empty
. When the radio has one segment left, the
radio chirps periodically or after releasing
(Low Battery Alert).
Removing the NiMH Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
3. Remove the NiMH battery pack by pulling the ribbon attached to
the radio.
4. Reposition the battery cover and press down to secure.
Removing the Three AA Batteries
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
3. Gently remove each alkaline battery by easing each battery
out individually.
4. Reposition the battery cover and press down to secure.
Notes
•
Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
• Remove the batteries before storing your radio for extended
periods of time. Batteries corrode over time and may cause
permanent damage to your radio.
Using the Battery Charger (Optional Accessory)
The battery charger provides drop-in charging convenience for
NiMH batteries and can be placed on any flat surface, such as a
desk or workbench. Charge the NiMH battery overnight (at least 16
hours) before using it for the first time. After the initial charge, an
empty battery is fully charged within 14 hours.
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk stand.
3. Plug the AC power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging
pockets.
5. When charging in the battery charger, the red light on the
charger base will glow continuously.
Two-Way Radio
User’s Guide
Using the mini-USB Charging Connector
The mini-USB charging connector is a handy port that allows you to
conveniently charge your NiMH battery pack. This is an alternative
to charging your NiMH battery pack in the Battery Charger desk
stand using the AC wall adaptor and especially useful when used
while traveling.
Available mini-USB charging options: (optional accessories)
1. Wall travel charger
2. Vehicle charger
3. Mini-USB computer cable
If using a computer, the computer must be turned on.
This and other accessories (sold separately) are available for
your radio. For more information, visit our Web site at
www.motorola.com.
1. Plug your mini-USB cable or charger into a power source as is
appropriate for your accessory.
2. Plug the cable into the mini-USB port on the bottom of your radio.
3. An empty battery will be fully charged in 14 hours.
4. The LED indicator light on the radio will glow to indicate that the
battery is charging.
Notes
•
The light will remain red after the NiMH battery pack is fully
charged.
•
When moving between hot and cold temperatures, do not
charge the NiMH battery pack until the battery temperature
acclimates (usually about 20 minutes).
•
For optimal battery life, remove the radio from the charger within
16 hours. Do not store the radio while connected to the charger.
•
If the radio is kept on while charging, the charging time will be
extended.
•
Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty . Allow
time for the battery to charge to 1 bar
before attempting to
transmit a message.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to
release the catch.
2. Pull the belt clip away from the back of the radio.
Turning your Radio On and Off
Turn
clockwise to turn the radio on and counterclockwise to
turn the radio off.
1. In the ON position, the radio chirps and briefly shows all feature
icons available on the radio.
2. The display screen then shows the current channel, code and
all features that are enabled.
Setting the Volume
Press and hold
for three seconds while rotating
until you
reach a comfortable listening level.
1. Rotate
clockwise to increase the volume.
2. Rotate
counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
1. To talk, press and hold
.
2. When you are finished talking, release
.
For maximum clarity, hold the radio two to three inches away from
your mouth and speak directly into the microphone. Do not cover
the microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Monitor Button
Pressing and holding
for three seconds allows you to listen to the
volume level of the radio when you are not receiving. This allows
you to adjust the volume, if necessary. You can also press
to
check for activity on the current channel before you talk.
Push-to-Talk
Timeout Timer
To prevent accidental transmissions and save battery life, the radio
emits a continuous warning tone and stops transmitting if you
press
for 60 continuous seconds.
For a fax:
Contact the
Fax-0n-Demand
system
For mail service:
Call the FCC
Forms Hotline
If you have
questions about
the FCC License:
Call the FCC
1-202-418-0177
1-800-418-FORM
(3676)
1-888-CALL-FCC
(225-5322)
Channels and Frequencies
Channel
Frequency
Description Channel
Frequency
Description
1
462.5625 MHz
GMRS
12
467.6625 MHz
FRS
2
462.5875 MHz
GMRS
13
467.6875 MHz
FRS
3
462.6125 MHz
GMRS
14
467.7125 MHz
FRS
4
462.6375 MHz
GMRS
15
462.5500 MHz
GMRS
5
462.6625 MHz
GMRS
16
462.5750 MHz
GMRS
6
462.6875 MHz
GMRS
17
462.6000 MHz
GMRS
7
462.7125 MHz
GMRS
18
462.6250 MHz
GMRS
8
467.5625 MHz
FRS
19
462.6500 MHz
GMRS
9
467.5875 MHz
FRS
20
462.6750 MHz
GMRS
10
467.6125 MHz
FRS
21
462.7000 MHz
GMRS
11
467.6375 MHz
FRS
22
462.7250 MHz
GMRS
Mexico
Use of GMRS frequencies is subject to the Rules and Regulations of
the Secretary of Communications and Transport (SCT) and Federal
Telecommunications Commissions (COFETEL). SCT/COFETEL
requires that all operators using GMRS frequencies obtain a permit
before operating their equipment. To obtain a permit from the SCT,
the user must proceed in accordance with Articles 14 and 15 of the
Federal Telecommunications Law. Consult your local SCT/COFETEL
office for more information: www.sct.gob.mx./www.cft.gob.mx.
Uruguay
Use of GMRS frequencies is subject to the Rules and Regulations of
the Regulatory Unit Communications Services (URSEC). URSEC
requires that all operators using GMRS frequencies obtain a permit
before operating their equipment. The authorization shall depend on
the channel availability at the time the authorization is requested. To
obtain a permit from URSEC, consult your local URSEC office for
more information: www.ursec.gub.uy.
Panama
The Republic of Panama does not require authorization to use
FRS/GMRS radio equipment frequencies.
USA
Use of GMRS frequencies is subject to the Rules and Regulations of
the Federal Communications Commission (FCC). The FCC requires
that all operators using GMRS frequencies obtain a radio license
before operating their equipment. To obtain the FCC forms, please
visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home
to source form 605 and 159, which include all the instructions you
will need.
If you wish to have the document faxed or mailed, or if you have
questions, please use the following contact information:
Canada
No license is required in Canada for GMRS use.
MJ Series_Hybrid.qxp:T5025_R 4/28/11 1:54 PM Page 1
