background image

8

 

STARLINE 

RF Amplifier Quick Start Guide 

 

Close the housing and use a torque wrench to sequentially and progressively tighten the 
housing bolts in the sequence specified on the housing cover.  

Torque the housing bolts to the following specifications: 

Amplifier Torque 

(ft-lbs.) 

BLE*/* 

MB*/*, 
MBE*/* 

12 

BT*/* 

15 

If You Need Help 

If you need assistance while working with the STARLINE amplifiers, contact the Motorola 
Technical Response Center (TRC): 

Inside the U.S.: 

1-888-944-HELP

 (

1-888-944-4357

Outside the U.S.: 

215-323-0044

 

Online: 

http://www.motorola.com/broadband

, click 

HTML/Modem Version

, click 

Customer Support

, then click 

Web Support

The TRC is open from 8:00 AM to 7:00 PM Eastern Time, Monday through Friday and 10:00 AM 
to 5:00 PM Eastern Time, Saturday. When the TRC is closed, emergency service 

only

 is 

available on a call-back basis. Web Support offers a searchable solutions database, technical 
documentation, and low priority issue creation/tracking 24 hours per day, 7 days per week. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOTOROLA, STARLINE and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service 
names are the property of their respective owners. 

 Motorola, Inc. 2002. 

498160-001 
8/02                   
 

All rights reserved. 
No part of the contents of this manual may be reproduced or transmitted in any form or by any means without the 
written permission of the publisher.

 

 

 

 

 

 

 

MGBI 

 

 

Summary of Contents for RF Amplifier









Reviews: