Motorola PTP 25600 User Manual Download Page 164

Page: 164 / 237

PTP 25600 reference information

Chapter 4 Reference information

phn-0896_009v003

4-16

UNDER DEVELOPMENT

Feb 2010

PTP 25600 reference information

This section contains reference information that is specific to the PTP 25600 frequency
variant.

PTP 25600 examples of regulatory limits

Table 4-10

shows how the regulatory limits currently apply in specific countries.

Operators should note that regulations are subject to change.

Table 4-10

PTP 25600 examples of regulatory limits

Region

Examples of Regulatory Limits at 2.5 GHz

FCC

Under FCC Regulations, operation of this product is only allowed with a
License Key for Region 16 which ensures that the product will meet the
requirements of FCC part 27.

Spectrum in this band (2496MHz to 2690MHz) is allocated on a licensed
basis in USA.

Summary of Contents for PTP 25600














































































































































































































































Search results

Summary of Contents for PTP 25600

Reviews:

Related manuals for PTP 25600

Brands by name

Popular brands

Motorola PTP 25600, User Manual

Search results

Summary of Contents for PTP 25600

Reviews:

Related manuals for PTP 25600

Brands by name

Popular brands