manualshive.com logo in svg

Motorola MPMC221, Installation And Use Manual, Page: 33 / 40

Share
Download
Motorola MPMC221 Installation And Use Manual Download Page 33

3

3-1

3

AIX Driver Installation

Overview

This chapter describes installation of the AIX device driver.

Before installing the AIX device driver, install the MPMC221/ 
MPMC222 on the carrier board per the instructions in Chapter 2, 
and install the carrier board into the system chassis.

Installing the AIX Driver

Follow these steps to install the IFDDI device driver using the AIX 
System Management Integration Tool (SMIT):

1. Log into host system as 

root

.

2. Insert the AIX Operating System CD-ROM into the CD-ROM 

drive on the host system.

3. Type the following at the command prompt and press 

Enter

.

smit devices

The Devices menu appears.

4. From the Devices menu, select 

Install Additional Device 

Software

.

A fill-in form appears, prompting you for the installation 
input device.

5. Use List to select the installation CD-ROM drive that contains 

the AIX software CD-ROM (example: 

/dev/cd0

).

6. Press 

Enter

.

A fill-in form appears, prompting you for the package you 
want to install.

Summary of Contents for MPMC221









































Reviews:

No comments