background image

6881096C46-O

December 2, 2003

Operation

: External Radio Operation

2-3

2.4

External Radio Operation

The External Radio feature amplifies and broadcasts incoming radio messages over the siren 
speaker, allowing radio communications to be heard outside the vehicle.

2.4.1

Control Head/DEK-Plus 

To enable the External Radio feature, turn the Siren function on by momentarily pressing the 

Siren

 

button on the DEK-Plus or the 

Sirn

 button on the control head. Then, select the External Radio 

function by pressing the 

Ex Rd

 button. The corresponding LEDs will illuminate. 

To adjust the External Radio volume, turn the volume control (rotary knob) on the control head. 

To turn off the External Radio feature, press the 

Siren

 button on the DEK-Plus or the 

Sirn

 button on 

the control head again, or select a different Siren function (Wail, Yelp, etc...). Once you turn off the 
External Radio function, the radio's receive volume will correspond with the position of the rotary 
knob on the control head.

2.5

Airhorn Operation

The Airhorn feature—available with the Control Head and DEK-Plus configurations—broadcasts an 
airhorn tone over the Siren speaker. To broadcast the Airhorn, momentarily press the 

Ar Hn

 button. 

To turn off the Airhorn, press the 

Ar Hn

 button again.

2.6

Manual Operation

The Manual function—available with the Control Head and DEK-Plus configurations—allows the 
Horn-Ring to activate a siren tone.

To enable the siren tone to be generated via the Horn-Ring, press the 

Man

 and 

Siren

 buttons. The 

corresponding LEDs will illuminate. Press the 

Horn-Ring

 to broadcast the pre-set tone (tones are 

programmed in the CPS, the default tone is “Wail”). You can program the Horn-Ring to generate the 
following tones:

• Manual Wail: Pressing the 

Horn-Ring

 activates a rising Wail that peaks at 1500 Hz and 

continues as long as the 

Horn-Ring

 is held. When you release the 

Horn-Ring

, the Wail tone 

falls until the tone is muted.

• Manual Yelp: Pressing the 

Horn-Ring

 activates a Yelp tone that continues as long as the 

Horn-

Ring

 is held. When you release the 

Horn-Ring

, the tone immediately mutes.

• Manual Airhorn: Pressing the 

Horn-Ring

 activates an airhorn sound that continues as long as 

the 

Horn-Ring

 is held. When you release the 

Horn-Ring

, the tone immediately mutes.

2.7

Speaker Protection Alert

When a short exists, the system performs a routine to “protect” itself from further harm. If a speaker 
short occurs, any audio broadcast (Siren functions, PA audio) is terminated. The Control Head 
displays 

SPKR SHORT

. When the problem is corrected, the Siren/PA returns to its previous operation.

In order for this feature to operate correctly, use only the 
following Motorola-approved speaker kits: TDN6251, 
TDN6252, TDN6253, and TDN6254. The use of any other 
speakers may cause unreliable operation of this feature and 
prevent proper operation of the Siren/PA.

!

C a u t i o n

Summary of Contents for MCS 2000















Reviews: