Motorola Malux MTM5400 Series Installation Manual Download

Page: 9 / 134

List of Figures

Figure 1: Power Cabling Routing to Engine Compartment.....................................................................41

Figure 2: Power Cable Assembly........................................................................................................... 42

Figure 3: Accessory Plug........................................................................................................................44

Figure 4: Radio with Mount Kit............................................................................................................... 46

Figure 5: Radio with Demount Tools...................................................................................................... 47

Figure 6: Typical Desktop Mounting....................................................................................................... 48

Figure 7: Remote Mount Installation with Remote Head Enhanced/Data Expansion Head

Enhanced.......................................................................................................................................... 49

Figure 8: Remote Mount Enhanced Control Head Installation with Remote Mount Trunnion................ 51

Figure 9: Remote Mount Enhanced Control Head Installation with DIN Mount Bracket........................ 52

Figure 10: Radio with Mounting Bracket and Mounting Kit.....................................................................53

Figure 11: Accessories Expansion Cable with the Mobile Microphone Port (MMP)...............................54

Figure 12: Remote Mount Installation with Ethernet Control Head (eCH) PMWN4024_....................... 55

Figure 13: Remote Mount Installation with Ethernet Telephone Style Control Head (TSCH)

PMWN4025_..................................................................................................................................... 56

Figure 14: Dual Control Head with Two eCH......................................................................................... 56

Figure 15: Dual Control Head with Two TSCH.......................................................................................57

Figure 16: Dual Control Head with a Combination of eCH and TSCH................................................... 57

Figure 17: Multi Radio Control Installation with eCH.............................................................................. 58

Figure 18: Multi Radio Control Installation with TSCH........................................................................... 58

Figure 19: Ethernet Cable (PMKN4141_, PMKN4140_, PMKN4139_, PMKN4138_, PMKN4136_,

and PMKN4146_).............................................................................................................................. 59

Figure 20: Ethernet Cable (PMKN4135_)...............................................................................................59

Figure 21: Ethernet Cable (PMKN4176_, PMKN4177_, and PMKN4178_)...........................................60

Figure 22: Remote Mount Enhanced Control Head Installation with Remote Mount Trunnion.............. 61

Figure 23: Remote Mount Enhanced Control Head Installation with DIN Mount Bracket...................... 62

Figure 24: Mounting the Remote Mount Enhanced Control Head with the DIN Mount Bracket into

the DIN Frame................................................................................................................................... 63

Figure 25: Accessories Expansion RECH Y-Cable................................................................................ 64

Figure 26: Accessories Expansion TSCH Y-Cable................................................................................ 66

Figure 27: Telephone Style Control Head (TSCH) Cradle..................................................................... 68

Figure 28: TSCH Handset and Cradle....................................................................................................69

Figure 29: TSCH Unsupported Installation.............................................................................................69

Figure 30: Slim Bracket.......................................................................................................................... 70

Figure 31: Rear View of TSCH Cradle................................................................................................... 71

Figure 32: Rear View of the TSCH Cradle with Slim Bracket.................................................................72

Figure 33: Rear View of the TSCH Cradle with Attached Slim Bracket .................................................73

68015000181-LB

List of Figures

Send Feedback

Summary of Contents for Malux MTM5400 Series






































































































































Search results

Summary of Contents for Malux MTM5400 Series

Reviews:

Related manuals for Malux MTM5400 Series

Brands by name

Popular brands

Motorola Malux MTM5400 Series, Installation Manual

Search results

Summary of Contents for Malux MTM5400 Series

Reviews:

Related manuals for Malux MTM5400 Series

Brands by name

Popular brands