Motorola DSP56309 User Manual Download Page 135 | Manualshive

Page: 135 / 425

background image

6-8

DSP56309UM/D MOTOROLA

Host Interface (HI08)

HI08 DSP Side ProgrammerÕs Model

6.5

HI08 DSP SIDE PROGRAMMERÕS MODEL

The DSP56309 core treats the HI08 as a memory-mapped peripheral occupying eight
24-bit words in X data memory space. The DSP treats the HI08 as a normal
memory-mapped peripheral, employing either standard polled or interrupt-driven
programming techniques. Separate transmit and receive data registers are
double-buffered to allow the DSP and host processor to transfer data efficiently at high
speed. Direct memory mapping allows the DSP56309 core to communicate with the HI08
registers using standard instructions and addressing modes. In addition, the MOVEP
instruction allows direct data transfers between DSP56309 internal memory and the
HI08 registers or

vice versa

.

There are two kinds of host processor registers, data and control, with eight registers in
all. All eight registers can be accessed by the DSP core but not by the external host.

Data registers are 24-bit registers used for high-speed data transfer to and from the DSP.

¥ Host data receive register (HRX)

¥ Host data transmit register (HTX)

The DSP side control registers are 16-bit registers that control DSP functions. The eight
MSBs in the DSP side control registers are read by the DSP56309 as 0. Those registers are
as follows:

¥ Host control register (HCR)

¥ Host status register (HSR)

¥ Host base address register (HBAR)

¥ Host port control register (HPCR)

¥ Host GPIO data direction register (HDDR)

¥ Host GPIO data register (HDR)

Both hardware RESET signals and software RESET instructions disable the HI08. After
reset, the HI08 signals are configured to GPIO and disconnected from the DSP56309 core
(i.e., the signals are left floating).

6.5.1

Host Receive Data Register (HRX)

The HRX register handles host-to-DSP data transfers. The DSP56309 views it as a 24-bit
read-only register. Its address is X:$FFFFC6. It is loaded with 24-bit data from the

«
...
133
134
135
136
137
...
»

Summary of Contents for DSP56309










































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56309

Brand: HAMILTON BEACH/PROCTOR SILEX Pages: 12

Brand: Waring Pages: 8

Brand: Yamaha Pages: 157

Brand: TECHWOOD Pages: 14

Brand: Sony Pages: 18

Brand: IRIS Pages: 42

Brand: Waring Pages: 22

Brand: Laretti Pages: 72

Brand: Vitek Pages: 24

MANUAL CHOPPER 5 seconds

Brand: TEFAL Pages: 13

Brand: cecotec Pages: 152

Brand: Johnson Pages: 40

Brand: Ultimate Chopper Pages: 4

Brand: Warsanis Pages: 23

Brand: Hamilton Beach Pages: 40

Brand: Fastwel Pages: 73

Brand: Harmony Pages: 6

Brand: Jabra Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands