manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

23-18

MCF5272 User’s Manual

 PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE

Debug AC Timing Specifications  

PRELIMINAR

Y

Figure 23-14. MII Serial Management Channel Timing Diagram

23.4.3  Timer Module AC Timing Specifications

Table 23-15 lists timer module AC timings.

Figure 23-15 shows timer module timings listed in Table 23-15. 

Table 23-15. Timer Module AC Timing Specifications

Name

Characteristic 

1

1

All timing references to SDCLK are given to its rising edge when bit 3 of the SDRAM control register is 0.

0–66 MHz

Unit

Min

Max

T1

TIN1 cycle time

3T

—

nS

T2

TIN1 valid to SDCLK (setup)

6

—

nS

T3

SDCLK to TIN[1:0] invalid (hold)

0

—

nS

T4

TIN1 pulse width

1T

—

nS

M11

MDC (output)

MDIO (output)

M12

M13

MDIO (input)

M10

M14

M15

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

dbx ProVocal Specifications preview
ProVocal
Brand: dbx Pages: 2
Digitus DN-7057 Quick Installation Manual preview
DN-7057
Brand: Digitus Pages: 8
ZALMAN RESERATOR 1 Manual preview
RESERATOR 1
Brand: ZALMAN Pages: 22
MF DIGITAL DIRECTOR PRO series Operator'S Manual preview
DIRECTOR PRO series
Brand: MF DIGITAL Pages: 79
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Brand: IFM Electronic Pages: 14
Freescale Semiconductor MPC8349EA MDS Getting Started Manual preview
MPC8349EA MDS
Brand: Freescale Semiconductor Pages: 8
Swann NVRx-7300 series Quick Start Manual preview
NVRx-7300 series
Brand: Swann Pages: 9
ZALMAN CNPS5X PERFORMA User Manual preview
CNPS5X PERFORMA
Brand: ZALMAN Pages: 8
Symantec SV1800 Series Safety And Regulatory Compliance Manual preview
SV1800 Series
Brand: Symantec Pages: 100
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Brand: Acromag Pages: 23
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
IceTech POD-51EH-C541U-12 Operating Instructions Manual preview
POD-51EH-C541U-12
Brand: IceTech Pages: 8
Intel IXP28 Series Manual preview
IXP28 Series
Brand: Intel Pages: 154
Vantec Aeroflow FX 120 VAF-1225 User Manual preview
Aeroflow FX 120 VAF-1225
Brand: Vantec Pages: 2
Digi NS7520B Series Hardware Reference Manual preview
NS7520B Series
Brand: Digi Pages: 339
ZALMAN CNPS2005-Plus User Manual preview
CNPS2005-Plus
Brand: ZALMAN Pages: 6

Brands by name

Popular brands

Load more brands