manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

 

Chapter 21.  IEEE 1149.1 Test Access Port (JTAG)

 

  

21-9

 

Non-IEEE 1149.1 Operation

 

21.7  Non-IEEE 1149.1 Operation 

 

In non-IEEE 1149.1 operation, IEEE 1149.1 test logic must be made transparent to system
logic by forcing the TAP controller into test-logic-reset state, which takes at least five
consecutive TCK rising edges with TMS high. TMS has an internal pull-up resistor and
may be left unconnected.

If TMS is unconnected or connected to V

 

CC

 

, the TAP controller cannot exit test-logic-reset

state, regardless of the TCK state. This requires the TMS, TCK, and TDI inputs to be high.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

8e6 Technologies Enterprise Filter Authentication R3000 Quick Start Manual preview
Enterprise Filter Authentication R3000
Brand: 8e6 Technologies Pages: 66
Fostex DE-1 Service Manual preview
DE-1
Brand: Fostex Pages: 20
Nvidia DGX A100 User Manual preview
DGX A100
Brand: Nvidia Pages: 115
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
A2B Electronics ECX-200 Installation Manual preview
ECX-200
Brand: A2B Electronics Pages: 24
ZALMAN CNPS6000-Al User Manual preview
CNPS6000-Al
Brand: ZALMAN Pages: 6
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
OPTO 22 PCI-AC48 User Manual preview
PCI-AC48
Brand: OPTO 22 Pages: 28
Quadram Quadboard Operation Manual preview
Quadboard
Brand: Quadram Pages: 21
ADS Technologies PTV-370 Driver Manual preview
PTV-370
Brand: ADS Technologies Pages: 1
CSL 300295 User Manual preview
300295
Brand: CSL Pages: 24
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Brand: WTI Pages: 178
Intel 80C186EC Manual preview
80C186EC
Brand: Intel Pages: 57
U-Media WST-375L User Manual preview
WST-375L
Brand: U-Media Pages: 42
Curtiss-Wright GTS/DEC/006 Instructions Manual preview
GTS/DEC/006
Brand: Curtiss-Wright Pages: 10
NetApp StorageGRID Webscale SG5700 Series Install preview
StorageGRID Webscale SG5700 Series
Brand: NetApp Pages: 15
Cambium Networks ePMP Elevate Quick Start Manual preview
ePMP Elevate
Brand: Cambium Networks Pages: 7
Jupiter AJ120 User Manual preview
AJ120
Brand: Jupiter Pages: 9

Brands by name

Popular brands

Load more brands