manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  20.  Bus Operation  

20-25

Reset Operation

NOTE:

Master reset must be asserted for all power-on resets. This is
done by driving RSTI and DRESETEN low simultaneously.
Failure to assert master reset during power-on sequences
results in unpredictable DRAM controller behavior.

20.12.1  Master Reset

To perform a master reset, an external device asserts RSTI and DRESETEN simultaneously
for a minimum of six CLKIN cycles after VDD is within tolerance. This should always be
done when power is initially applied. A master reset resets the entire device including the
SDRAM controller.

Figure 20-21 is a functional timing diagram of the master reset operation, illustrating
relationships among VDD, RSTI, DRESETEN, RSTO, mode selects, and bus signals.

CLKIN must be stable by the time VDD reaches the minimum operating specification.
RSTI and DRESETEN are internally synchronized on consecutive rising and falling clocks
before being used. They must meet the specified setup and hold times to the falling edge of
CLKIN only if recognition by a specific falling edge is required

.

Figure 20-21. Master Reset Timing

When the assertion of RSTI is recognized internally, the MCF5272 asserts the reset out pin
(RSTO). The RSTO pin is asserted as long as RSTI is asserted and remains asserted for
32,768 CLKIN cycles after RSTI is negated.

During the master reset period, all outputs are driven to their default levels. Once RSTO
negates, all bus signals continue to remain in this state until the ColdFire core begins the
first bus cycle for reset exception processing.

VDD

RSTI

Mode Select

CLKIN

RSTO

T >= 6

CLK CYCLES

T = 32,768

CLK CYCLES

T >= 22

CLK CYCLES

BUS SIGNALS

DRESETEN

Inputs

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

3Com IntelliJack NJ200 Datasheet preview
IntelliJack NJ200
Brand: 3Com Pages: 4
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
JYTEK PCIe/PXIe-6301 Series User Manual preview
PCIe/PXIe-6301 Series
Brand: JYTEK Pages: 46
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
Commell FS-A79 User Manual preview
FS-A79
Brand: Commell Pages: 36
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Brand: ekwb Pages: 2
Aviosys 9255W User Manual preview
9255W
Brand: Aviosys Pages: 77
NXP Semiconductors RDGD3160I3PH5EVB User Manual preview
RDGD3160I3PH5EVB
Brand: NXP Semiconductors Pages: 21
Alcatel-Lucent Service Aggregation Router 7705 Installation Manual preview
Service Aggregation Router 7705
Brand: Alcatel-Lucent Pages: 20
Renesas H8SX1664 User Manual preview
H8SX1664
Brand: Renesas Pages: 21
Parker Sporlan Division SCS-PB Series Installation And Operating Instructions Manual preview
Sporlan Division SCS-PB Series
Brand: Parker Pages: 10
Vxl IQL Series Hardware Installation Manual preview
IQL Series
Brand: Vxl Pages: 4
ST X-NUCLEO-AMICAM1 User Manual preview
X-NUCLEO-AMICAM1
Brand: ST Pages: 18
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Brand: Bdcom Pages: 25
AG AstroPC PRO User Manual preview
AstroPC PRO
Brand: AG Pages: 10

Brands by name

Popular brands

Load more brands