manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  19.  Signal Descriptions  

19-29

Physical Layer Interface Controller TDM Ports

19.14.6  Synchronous Peripheral Chip Select 2 

(QSPI_CS2/URT1_CTS)

See Section 19.15.1.5, “UART1 CTS (URT1_CTS/QSPI_CS2).” 

19.14.7  Synchronous Peripheral Chip Select 3 

(PA7/DOUT3/QSPI_CS3)

See Section 

19.15.3.3, “QSPI_CS3, Port 3 GCI/IDL Data Out 3, PA7

(PA7/DOUT3/QSPI_CS3).”

See description for GPIO ports.

QSPI_CS3 can be programmed to be active high or low.

19.15  Physical Layer Interface Controller TDM Ports

The MCF5272 has four dedicated physical layer interface ports for connecting to external
ISDN transceivers, CODECs and other peripherals. There are three sets of pins for these
interfaces. Port 0 has its own dedicated set of pins. Ports 1, 2, and 3 share a set of pins.
Port 3 can also be configured to use a dedicated pin set. Ports 1, 2, and 3 always share the
same data clock, (DCL).

19.15.1  GCI/IDL TDM Port 0.

This section describes signals used by the PLIC module port 0 interface.

19.15.1.1  Frame Sync (FSR0/FSC0/PA8)

IDL mode: FSR0 is an input for the 8-KHz frame sync for port 0. 

GCI mode: FSC0 is an input for the 8-KHz frame sync for port 0. It is active high in this
mode. Normally the GCI FSC signal is two clocks wide and is aligned with the first
B-channel bit of the GCI frame. Many U-interface devices including the MC145572 and
MC145576 change the width of FSC to one clock every 12 mS. This indicates U-interface
super frame boundary.

Port A mode: This pin can be independently configured as PA8.

19.15.1.2  D-Channel Grant (DGNT0/PA9)

IDL mode: This pin can be independently configured as the input, DGNT0, used by a
layer-one ISDN S/T transceiver to indicate that D-channel access has been granted.

Port A mode: This pin can be independently configured as I/O pin PA9.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Brand: Cabletron Systems Pages: 21
Idis DR-8416 Operation Manual preview
DR-8416
Brand: Idis Pages: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Brand: Idis Pages: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Brand: Idis Pages: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Brand: Idis Pages: 82
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Brand: Renesas Pages: 17
Velopex Extra-X Quick Start Manual preview
Extra-X
Brand: Velopex Pages: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
JETWAY LI1B Series User Manual preview
LI1B Series
Brand: JETWAY Pages: 55
Intel F-Tile SDI II Intel Agilex User Manual preview
F-Tile SDI II Intel Agilex
Brand: Intel Pages: 39
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
Digi ConnectCore 8X Hardware Reference Manual preview
ConnectCore 8X
Brand: Digi Pages: 116
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
Segger J-Link-OB-STM32F072-128KB User Manual preview
J-Link-OB-STM32F072-128KB
Brand: Segger Pages: 18
Seagate CHEETAH ST34501FC Product Manual preview
CHEETAH ST34501FC
Brand: Seagate Pages: 68
Laser UDC CARD User Manual preview
UDC CARD
Brand: Laser Pages: 4
IEI Technology WAFER-ULT4 User Manual preview
WAFER-ULT4
Brand: IEI Technology Pages: 136

Brands by name

Popular brands

Load more brands