manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

 

14-12

 

MCF5272 User’s Manual

 

 

 

Programming Model  

 

14.5.3  QSPI Wrap Register (QWR)

 

Table 14-5 gives QWR field descriptions.

 

14.5.4  QSPI Interrupt Register (QIR)

 

Figure 14-7 shows the QSPI interrupt register.

 

15

14

13

12

11

8

7

4

3

0

 

Field

HALT WREN

WRTO CSIV

ENDQP

 

–

 

NEWQP

Reset

0000_0000_0000_0000

R/W

R/W

Address

MBAR + 0x00A8

 

Figure 14-6. QSPI Wrap Register (QWR)

Table 14-5. QWR Field Descriptions 

 

Bits

Name

Description

 

15

HALT

Halt transfers. Assertion of this bit causes the QSPI to stop execution of commands once 
it has completed execution of the current command.

14

WREN

Wraparound enable. Enables wraparound mode.
0 Execution stops after executing the command pointed to by QWR[ENDQP].
1 After executing command pointed to by QWR[ENDQP], wrap back to entry zero, or the 

entry pointed to by QWR[NEWQP] and continue execution.

13

WRTO

Wraparound location. Determines where the QSPI wraps to in wraparound mode.
0 Wrap to RAM entry zero.
1 Wrap to RAM entry pointed to by QWR[NEWQP].

12

CSIV

QSPI_CS inactive level.
0 QSPI chip select outputs return to zero when not driven from the value in the current 

command RAM entry during a transfer (that is, inactive state is 0, chip selects are 
active high).

1 QSPI chip select outputs return to one when not driven from the value in the current 

command RAM entry during a transfer (that is, inactive state is 1, chip selects are 
active low).

11–8

ENDQP

End of queue pointer. Points to the RAM entry that contains the last transfer description 
in the queue. 

7–4

CPTQP

Completed queue entry pointer. Points to the RAM entry that contains the last command 
to have been completed. This field is read only.

3–0

NEWQP Start of queue pointer. This 4-bit field points to the first entry in the RAM to be executed 

on initiating a transfer.

 

15

14

13

12

11

10

9

8

7

4

3

2

1

0

 

Field

WCEFB ABRTB

— ABRTL WCEFE ABRTE

— SPIFE

—

WCEF ABRT

— SPIF

Reset

0000_0000_0000_0000

R/W

R/W

Address

MBAR + 0x00AC

 

Figure 14-7. QSPI Interrupt Register (QIR)

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Harman Kardon CITATION 7.0 Owner'S Manual preview
CITATION 7.0
Brand: Harman Kardon Pages: 66
Yamaha EMP100 Supplementary Manual preview
EMP100
Brand: Yamaha Pages: 4
IBM 8677 - BladeCenter Rack-mountable - Power... Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power...
Brand: IBM Pages: 126
Commell ES-270 User Manual preview
ES-270
Brand: Commell Pages: 36
Freescale Semiconductor FRDM-STBC-SA9500 Quick Reference Card preview
FRDM-STBC-SA9500
Brand: Freescale Semiconductor Pages: 2
TDK HHM Series HHM2411 Specification Sheet preview
HHM Series HHM2411
Brand: TDK Pages: 2
Avaya XM24 Expansion Module Installation Instructions preview
XM24 Expansion Module
Brand: Avaya Pages: 5
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
National Instruments SCXI-1120 User Manual preview
SCXI-1120
Brand: National Instruments Pages: 130
NXP Semiconductors RDGD3160I3PH5EVB User Manual preview
RDGD3160I3PH5EVB
Brand: NXP Semiconductors Pages: 21
Cutting Edge Unity AM Manual preview
Unity AM
Brand: Cutting Edge Pages: 92
ADLINK Technology EOS-1200 User Manual preview
EOS-1200
Brand: ADLINK Technology Pages: 108
ZALMAN CNPS10X Flex User Manual preview
CNPS10X Flex
Brand: ZALMAN Pages: 12
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Brand: Kontron Pages: 20
AXIOMTEK tBOX312-870-FL Quick Installation Manual preview
tBOX312-870-FL
Brand: AXIOMTEK Pages: 2
IBASE Technology ET880 Series User Manual preview
ET880 Series
Brand: IBASE Technology Pages: 64
Faroudja DVP2200 Installation And Operation Manual preview
DVP2200
Brand: Faroudja Pages: 17
Abocom LA100 Quick Installation Manual preview
LA100
Brand: Abocom Pages: 20

Brands by name

Popular brands

Load more brands