manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

 

Chapter 14.  Queued Serial Peripheral Interface (QSPI) Module

 

  

14-3

 

Operation

 

14.3.2  Internal Bus Interface

 

Because the QSPI module only operates in master mode, the master bit in the QSPI mode
register (QMR[MSTR]) must be set for the QSPI to function properly. The QSPI can
initiate serial transfers but cannot respond to transfers initiated by other QSPI masters.

 

14.4  Operation

 

The QSPI uses a dedicated 80-byte block of static RAM accessible both to the module and
the CPU to perform queued operations. The RAM is divided into three segments as follows:

•

16 command control bytes (command RAM)

•

16 transmit data words, (transfer RAM)

•

16 receive data words (transfer RAM)

RAM is organized so that 1 byte of command control data, 1 word of transmit data, and 1
word of receive data comprise 1 queue entry, 0x0–0xF.

The user initiates QSPI operation by loading a queue of commands in command RAM,
writing transmit data into transmit RAM, and then enabling the QSPI data transfer. The
QSPI executes the queued commands and sets the completion flag in the QSPI interrupt
register (QIR[SPIF]) to signal their completion. Optionally, QIR[SPIFE] can be enabled to
generate an interrupt.

The QSPI uses four queue pointers. The user can access three of them through fields in
QSPI wrap register (QWR): 

•

The new queue pointer, QWR[NEWQP], points to the first command in the queue.

•

An internal queue pointer points to the command currently being executed.

•

The completed queue pointer, QWR[CPTQP], points to the last command executed. 

•

The end queue pointer, QWR[ENDQP], points to the final command in the queue.

The internal pointer is initialized to the same value as QWR[NEWQP]. During normal
operation, the following sequence repeats:

1. The command pointed to by the internal pointer is executed.

2. The value in the internal pointer is copied into QWR[CPTQP].

3. The internal pointer is incremented.

 

Table 14-1. QSPI Input and Output Signals and Functions

 

Signal Name

Hi-Z or Actively Driven

Function

 

QSPI Data Output (QSPI_Dout)

Configurable

Serial data output from QSPI

QSPI Data Input (QSPI_Din)

N/A

Serial data input to QSPI

Serial Clock (QSPI_CLK)

Actively driven

Clock output from QSPI

Peripheral Chip Selects (QSPI_CS[3:0])

Actively driven

Peripheral selects

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
National Instruments SCXI-1121 User Manual preview
SCXI-1121
Brand: National Instruments Pages: 162
NXP Semiconductors TWR-SB0410-36EVB User Manual preview
TWR-SB0410-36EVB
Brand: NXP Semiconductors Pages: 26
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Brand: 8e6 Technologies Pages: 74
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Brand: ZALMAN Pages: 9
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
A4Tech RG-71M User Manual preview
RG-71M
Brand: A4Tech Pages: 7
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
S&T Kontron SMARC-sXEL User Manual preview
Kontron SMARC-sXEL
Brand: S&T Pages: 108
Aviosys 9255W User Manual preview
9255W
Brand: Aviosys Pages: 77
Lattice Semiconductor LatticeMico GPIO Manual preview
LatticeMico GPIO
Brand: Lattice Semiconductor Pages: 28
8e6 Technologies HL-002-006 Quick Start Manual preview
HL-002-006
Brand: 8e6 Technologies Pages: 94
WIN Enterprises PL-83300 User Manual preview
PL-83300
Brand: WIN Enterprises Pages: 25
Z3 Technology FSDI-1XA User Manual preview
FSDI-1XA
Brand: Z3 Technology Pages: 83

Brands by name

Popular brands

Load more brands