Motorola DigitalDNA ColdFire MCF5272 User Manual Download Page 321 | Manualshive

Page: 321 / 550

background image

Chapter 13. Physical Layer Interface Controller (PLIC)

13-27

PLIC Registers

13.5.13 GCI Monitor Channel Transmit Registers

(P0GMT–P3GMT)

All bits in these registers are read/write and are cleared on hardware or software reset.

The PLGMT registers are 16 bit register containing the control and monitor channel bits to
be transmitted for each of the four ports on the MCF5272.

A byte of monitor channel data to be transmitted on a certain port is put into an associated
register using the format shown in Figure 13-25. A maskable interrupt is generated when
this byte of data has been successfully transmitted.

8

MC

Monitor change.
0 Default at reset.
1 Indicates to the CPU that the monitor channel data byte written to the respective

PLGMR register has changed and that the data is available for processing.
Automatically cleared by the CPU when the PLGMR register has been read.
Clearing this bit by reading this register also clears the aperiodic GMR interrupt.

7–0

M

Monitor channel data byte.

15

10

9

8

7

0

Field

—

L

R

M

Reset

0000_0000_0000_0000

R/W

Read/Write

Addr

MBAR + 0x368 (P0GMT); 0x36A (P1GMT); 0x36C (P2GMT); 0x36E (P3GMT)

Figure 13-25. GCI Monitor Channel Transmit Registers (P0GMT–P3GMT)

Table 13-8. P0GMT–P3GMT Field Descriptions

Bits

Name

Description

15–10

—

Reserved, should be cleared.

9

L

Last.
0 Default reset value
1 Set by the CPU. Indicates to the monitor channel controller to transmit the end of message signal

on the E bit. Both PnGMT[L] and PnGMT[R] must be set for the monitor channel controller to send
the end of message signal. PnGMT[M7:0] are ignored and 0xFF is sent with the end of message
condition necessitating sending the monitor channel information using PnGMT[R] to control the
monitor channel transmitter, followed at the end of the frame by setting PnGMT[L] and PnGMT[R].
The L bit is automatically cleared by the GCI controller.

8

R

Ready.
0 Default reset value.
1 Set by the CPU. Indicate to the monitor channel controller that a byte of data is ready for

transmission. Automatically cleared by the GCI controller when it generates a transmit
acknowledge (ACK bit in PGMTS register) or when the L bit is reset.

7–0

M

Monitor channel data byte. Written by the CPU when a byte is ready for transmission.

Table 13-7. P0GMR–P3GMR Field Descriptions

Bits

Name

Description

«
...
319
320
321
322
323
...
»

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Brand: NAIM Pages: 2

Brand: Intel Pages: 958

Brand: Microchip Technology Pages: 9

Brand: Dahua Pages: 113

Brand: Nortel Pages: 163

Brand: Baracoda Pages: 16

STEVAL-SCR002V1

Brand: ST Pages: 28

Brand: ADLINK Technology Pages: 95

Brand: NUROTRON Pages: 16

Brand: R3 Pages: 48

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

Brand: Sun Microsystems Pages: 410

Dummy IC M3T-SSOP36B-450

Brand: Renesas Pages: 4

2 Channel Inductor Module CLX-2IND

Brand: Crestron Pages: 1

Quantum Ultra Series

Brand: Extron electronics Pages: 125

Brand: NetApp Pages: 121

Brand: KE2 Therm Solutions Pages: 26

Brand: SunFounder Pages: 527

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands