manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter 13.  Physical Layer Interface Controller (PLIC)  

13-21

PLIC Registers

13.5.8  Loopback Control Register (PLCR)

All bits in this register are cleared on hardware or software reset. 

The PLCR is an 8-bit register containing the configuration information for all four ports on
the MCF5272. 

 11

M/S

Master/Slave. Defines the direction of the DCL1 and FSC1 pins. 
0 DCL1 and FSC1 are inputs and are sourced from an external master. Note: This bit is relevant to 

port 1 only, as port 0 is always in slave mode.

1 enables DCL1 and FSC1 to be outputs, that is, the MCF5272 drives DCL1 and FSC1. 

10

G/S

GCI/SCIT. 
0 The normal mode of GCI is used (i.e. no D-channel contention control).
1 Selects SCIT mode of operation for the GCI interfaces. 

 9

FSM

Frame Sync Master. 
0  Default reset value. 2-KHz interrupt is generated from port 0. 
1 Port 1 FSC/FSR is used to generate the 2-KHz interrupt.

8

ACT

GCI Activation. 
0 Default reset value.
1 Causes Dout to transition to a logic low for the respective port. This bit is only operational when 
the port is in GCI mode. Setting the ACT bit in any other mode has no effect. It is the responsibility 
of the CPU to clear the ACT bit when normal operation on Dout is required. This bit is intended to 
be used to request activation from the upstream DCL/FSC driver. Periodic interrupts commence as 
soon as the upstream device generates DCL, provided the appropriate interrupts, such as IE, 
B1RIE, and so on, are enabled for the port.

7

DMX

Data multiplex.
0 port 3 Dout and Din are multiplexed onto Dout1 and Din1.
1 enables port 3 Dout and Din to be connected to dedicated output and input pins, DOUT3 and 

DIN3.

3

SHB2

B2 channel shift direction. 
0 B2 channel data is received/transmitted msb first. The msb-first convention is often used for 

communication with PCM CODECs and converters.

1 B2 channel data is received/transmitted lsb first. The lsb-first convention is used when the data is 

to be HDLC encoded.

2

SHB1

B1 channel shift direction. See SHB2.

 1

ENB2

Enable B2 data channel. 
0 The B2 channel is disabled and all periodic interrupts in both receive and transmit directions are 

disabled. The behavior of Din and Dout in this state is shown below.

1 Enables the B2 data channel for the respective port. 

0

ENB1

Enable B1 data channel. See ENB2.

Table 13-2. P0CR–P3CR Field Descriptions (Continued)

Bits

Name

Description

Mode

Din

Dout

IDL

All 1s

High Impedance

GCI

Operational (data on 
Din visible)

Open drain

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Xinje XS Series User Manual preview
XS Series
Brand: Xinje Pages: 57
Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Avaya PARTNER PC CARD Installation Instructions preview
PARTNER PC CARD
Brand: Avaya Pages: 4
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
Juniper NFX250 Quick Start Manual preview
NFX250
Brand: Juniper Pages: 7
RANA Systems Elite Controller User Manual preview
Elite Controller
Brand: RANA Systems Pages: 328
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Brand: Delta Electronics Pages: 1
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Brand: Advantech Pages: 96
National Instruments IMAQTM User Manual preview
IMAQTM
Brand: National Instruments Pages: 121
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
Navitar 1-62643 Dimensional Drawing preview
1-62643
Brand: Navitar Pages: 1
Stepper Motor Canada DB25-1205F Manual preview
DB25-1205F
Brand: Stepper Motor Canada Pages: 5
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
ST X-NUCLEO-EEPRMA1 User Manual preview
X-NUCLEO-EEPRMA1
Brand: ST Pages: 22
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Brand: IMC Networks Pages: 13
LevelOne NVR-0432 User Manual preview
NVR-0432
Brand: LevelOne Pages: 142
Renesas M32173T-PTC User Manual preview
M32173T-PTC
Brand: Renesas Pages: 7

Brands by name

Popular brands

Load more brands