manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter 13.  Physical Layer Interface Controller (PLIC)  

13-11

GCI/IDL Block

13.2.5  GCI/IDL Interrupts

The PLIC module generates two interrupts—the periodic frame interrupt and the aperiodic
status interrupt.

13.2.5.1  GCI/IDL Periodic Frame Interrupt

The frame interrupt is a periodic 2-KHz interrupt as shown in Figure 13-10. This is the
normal interrupt rate for servicing the incoming and outgoing B and D channels. This
service routine must execute in a timely manner. Each of the B- and D-channel transmit and
receive registers should be written and read prior to the next 2-KHz interrupt for underrun
or overrun conditions to be prevented.

Note that only the active, that is enabled, B- and D-channel receive and transmit registers
need to be read and written. B and D channels which are not active need not have their
receive and transmit registers read and written.

Figure 13-10. Periodic Frame Interrupt

It should be clear from Figure 13-10 that due to the double buffering through the PLIC
shadow register, frame (n) is written to the PLIC transmit register during the interrupt
service routine of the previous frame, frame (n-1). Similarly on the receive side, frame (n)
is read from the PLIC receive register during the interrupt service routine of the following
frame, frame (n + 2). Figure 13-10 shows that the minimum delay through the PLIC, when
not in loopback mode, is two 2-KHz frames, or 1 mS.

13.2.5.2   GCI Aperiodic Status Interrupt

The aperiodic status interrupt is an interrupt which is driven by a number of conditions. The
CPU services this interrupt by reading the aperiodic status register, ASR, and by reading or
writing the relevant C/I or monitor channel register or registers which have generated this

Slot 0

Slot 1

Slot 2

Slot 3

Frame n

Frame n  +  1

2-KHz interrupt

2-KHz interrupt

 

Interrupt service routine

Read Frame n -1 (B&D)

Write Frame n  +  1 (B&D)

Interrupt service routine

Read Frame n (B&D)

Write Frame n  +  2 (B&D)

Interrupt service routine

Read Frame n  +  1 (B&D)

Write Frame n  +  3 (B&D)

 

500 

 

µ

 

s

125 

 

µ

 

s

Slot 0

Slot 1

Slot 2

Slot 3

Slot 0

Slot 1

Frame n  +  2

Slot 2

2-KHz interrupt

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Patton electronics 1090 Service Manual preview
1090
Brand: Patton electronics Pages: 8
National Instruments PXIe-8240 Getting Started preview
PXIe-8240
Brand: National Instruments Pages: 9
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 8
XESS XStend XS40 User Manual preview
XStend XS40
Brand: XESS Pages: 23
Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Brand: Blackrock Microsystems Pages: 27
Behringer EXPANSION CARD X-DANTE Quick Start Manual preview
EXPANSION CARD X-DANTE
Brand: Behringer Pages: 65
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
Cateye Urban Wireless CC-VT240W Instruction Manual preview
Urban Wireless CC-VT240W
Brand: Cateye Pages: 15
Gate NanoAAB User Manual preview
NanoAAB
Brand: Gate Pages: 8
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
Icy Box IB-NAS5520 Quick Start Manual preview
IB-NAS5520
Brand: Icy Box Pages: 2
Omron NJ501-1300 User Manual preview
NJ501-1300
Brand: Omron Pages: 432
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Brand: Avigilon Pages: 12
Kontron ADA-SDVO-PEG16 User Manual preview
ADA-SDVO-PEG16
Brand: Kontron Pages: 14
Datavideo NVW-150 Instruction Manual preview
NVW-150
Brand: Datavideo Pages: 71
Compaq ProLiant 4500 Quick Start Manual preview
ProLiant 4500
Brand: Compaq Pages: 2

Brands by name

Popular brands

Load more brands