manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

11-26

MCF5272 User’s Manual

 

Programming Model  

11.5.16  RAM Perfect Match Address Low (ADDR_LOW)

The ADDR_LOW register contains the lower 32 bits of the 48 bit MAC address used in the
address recognition process to compare with the Destination Address field of the receive
frames.

This register, shown in Figure 11-19, is not reset and must be initialized by the user prior
to operation.

11.5.16.1  RAM Perfect Match Address High (ADDR_HIGH)

The ADDR_HIGH register contains bytes 4 and 5 of the 48-bit MAC address used in the
address recognition process to compare with the destination address field of the receive
frames. Byte 0 is the first byte transmitted on the network at the start of the frame.

This register is not reset and must be initialized by the user prior to operation. See

1

HBC

Heartbeat control. If set, the heartbeat check is performed following end of transmission and 
the HB bit in the status register is set if the collision input does not assert within the heartbeat 
window. This bit should be modified only when ETHER_EN is deasserted.

0

GTS

Graceful transmit stop. When this bit is set, the MAC stops transmission after any current 
frame is complete and the GRA interrupt in the INTR_EVENT register is asserted. If frame 
transmission is not currently underway, the GRA interrupt is asserted immediately. Once 
transmission is complete, a restart is accomplished by clearing the GTS bit. The next frame in 
the transmit FIFO is then transmitted. If an early collision occurs during transmission when 
GTS = 1, transmission stops after the collision. The frame is transmitted again once GTS is 
cleared. Note that there may be old frames in the transmit FIFO that are transmitted when 
GTS is reasserted. To avoid this, deassert ETHER_EN following the GRA interrupt.

31

16

Field

ADDR_LOW

Reset

Undefined

R/W

Read/Write

15

0

Field

ADDR_LOW

Reset

Undefined

R/W

Read/Write

Addr

MBAR + 0xC00

Figure 11-19. RAM Perfect Match Address Low (ADDR_LOW)

Table 11-23. ADDR_LOW Field Descriptions

Bits

Name

Description

31–0

ADDR_LOW

Bytes 0 (bits 31–24), 1 (bits 23–16), 2 (bits 15:8), and 3 (bits 7–0) of the 6-byte address.

Table 11-22. X_CNTRL Field Descriptions (Continued)

Bits

Name

Description

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
Hal Communications RS2100 Instruction Manual preview
RS2100
Brand: Hal Communications Pages: 25
Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual preview
CLICK PLUS C2-02CPU
Brand: Automationdirect.com Pages: 10
EK-Quantum Kinetic FLT 80 D5/DDC Body User Manual preview
Kinetic FLT 80 D5/DDC Body
Brand: EK-Quantum Pages: 16
ICT Protege PRT-PX16-PCB Installation Manual preview
Protege PRT-PX16-PCB
Brand: ICT Pages: 34
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Brand: B&B Electronics Pages: 16
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Brand: IDT Pages: 98
Keithley DAS-1800HR Series User Manual preview
DAS-1800HR Series
Brand: Keithley Pages: 139
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Brand: VIA Technologies Pages: 25
ST X-NUCLEO-EEPRMA1 User Manual preview
X-NUCLEO-EEPRMA1
Brand: ST Pages: 22
H3C BT1004E Manual preview
BT1004E
Brand: H3C Pages: 34
MEN ME4 User Manual preview
ME4
Brand: MEN Pages: 48
Abus TVAC21000 User Manual preview
TVAC21000
Brand: Abus Pages: 98
Axtrinet APG200 User Manual preview
APG200
Brand: Axtrinet Pages: 49
DMX4ALL DMX-Relais 2 INRUSH User Manual preview
DMX-Relais 2 INRUSH
Brand: DMX4ALL Pages: 18
Acromag XVPX-6300 User Manual preview
XVPX-6300
Brand: Acromag Pages: 20
ADTRAN NetVanta 1224 Quick Start Manual preview
NetVanta 1224
Brand: ADTRAN Pages: 2
ADTRAN 1200934L1 Installation Instructions preview
1200934L1
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands