Motorola DigitalDNA ColdFire MCF5272 User Manual Download Page 156 | Manualshive

Page: 156 / 550

background image

5-44

MCF5272 User’s Manual

Processor Status, DDATA Definition

Exception Processing

PST = 0xC,

{PST = 0xB,DD = destination},

// stack frame

{PST = 0xB,DD = destination},

// stack frame

{PST = 0xB,DD = source},

// vector read

PST = 0x5,

{PST = [0x9AB],DD = target}

// handler PC

The PST/DDATA specification for the reset exception is shown below:

Exception Processing

PST = 0xC,
PST = 0x5,

{PST = [0x9AB],DD = target}

// handler PC

The initial references at address 0 and 4 are never captured nor displayed since these
accesses are treated as instruction fetches.

For all types of exception processing, the PST = 0xC value is driven at all times, unless the
PST output is needed for one of the optional marker values or for the taken branch indicator
(0x5).

5.7.2 Supervisor Instruction Set

The supervisor instruction set has complete access to the user mode instructions plus the
opcodes shown below. The PST/DDATA specification for these opcodes is shown in
Table 5-23.

The move-to-SR and RTE instructions include an optional PST = 0x3 value, indicating an
entry into user mode. Additionally, if the execution of a RTE instruction returns the
processor to emulator mode, a multiple-cycle status of 0xD is signaled.

Similar to the exception processing mode, the stopped state (PST = 0xE) and the halted
state (PST = 0xF) display this status throughout the entire time the ColdFire processor is in
the given mode.

Table 5-23. PST/DDATA Specification for Supervisor-Mode Instructions

Instruction

Operand Syntax

PST/DDATA

cpushl

PST = 0x1

halt

PST = 0x1,
PST = 0xF

move.w

SR,Dx

PST = 0x1

move.w

{Dy,#imm},SR

PST = 0x1, {PST = 0x3}

movec

Ry,Rc

PST = 0x1

rte

PST = 0x7, {PST = 0xB, DD = source operand}, {PST = 3}, { PST = 0xB,
DD = source operand},
PST = 0x5, {[PST = 0x9AB], DD = target address}

stop

#imm

PST = 0x1,
PST = 0xE

wdebug

<ea>y

PST = 0x1, {PST = 0xB, DD = source, PST = 0xB, DD = source}

«
...
154
155
156
157
158
...
»

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Brand: Samsung Pages: 2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 15

Brand: LAWO Pages: 154

Brand: VMIC Pages: 126

Brand: ekwb Pages: 2

Brand: Acces I/O products Pages: 5

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

Brand: Parker Pages: 50

Brand: Kanguru Pages: 13

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brand: Supersonic Pages: 46

Brand: Alarm Pages: 5

Disc Publisher XR

Brand: Primera Pages: 2

Brand: ADS Technologies Pages: 1

Brand: CSL Pages: 24

Brand: Kontron Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands