Motorola c18 Developer'S Manual Download Page 40 | Manualshive

Page: 40 / 82

background image

Hardware Description

32

98-08901C63-A

3.7.5

Digital Audio Interface

Digital audio signals can be used as general-purpose I/Os when the digital audio interface is not needed. Table 12 lists the c18
digital audio interface signals.

3.8

ANTENNA

This section describes the available RF antenna connectors and their requirements.

3.8.1

RF Connectors

Two female MMCX antenna connectors are provided for RF input/output in the c18 module:

• Cellular Bands Antenna Connector (J31)
• GPS Antenna Connector (J30)
Both RF connectors (J30 and J31) are 50-ohm connectors with VSWR less than 2:1. Figure 18 shows the c18 module’s antenna
connectors.

There are three supported antenna port configurations, as follows:

• A single-port solution that supports CDMA1X/AMPS/GPS bands (with a passive antenna) using the J31 connector.
• A single-port solution that supports CDMA1X/AMPS bands only using the J31 connector.
• A dual-port solution in which the J31 connector is used to support CDMA1X/AMPS only, and the J30 connector is used to

support the GPS band (with an active or passive antenna).

Table 12. Digital Audio Interface Signals

Signal Name

70-pin Connector

Pin Number

Description

PCM_DIN_GPIO1

18

PCM input to c18

PCM_DOUT_GPIO2

20

PCM output from c18

PCM_CLK_GPIO3

22

PCM Clock signal

PCM_FS_GPIO4

24

PCM Sync signal

Note

Digital audio is hardware supported.

«
...
38
39
40
41
42
...
»

Summary of Contents for c18



















































































Reviews:

No comments

Related manuals for c18

Brand: BAFANG Pages: 4

Brand: O.S. engine Pages: 5

MAX-15CV-R Series

Brand: O.S. engine Pages: 19

CentriPro Xtreme Duty Series

Brand: Xylem Pages: 12

Vanguard Diesel 432447

Brand: Briggs & Stratton Pages: 24

Brand: Grundfos Pages: 25

MerCruiser Diesel Inboard 2.8L

Brand: Mercury Pages: 93

Brand: Rotax Pages: 13

Brand: Perkins Pages: 42

Brand: Bodine Pages: 8

Brand: MINN KOTA Pages: 3

Brand: MINN KOTA Pages: 4

Brand: Caple Pages: 16

Brand: Canaline Pages: 43

Brand: WÜRGES Pages: 4

Brand: AE Pages: 4

Brand: ARO Pages: 8

Brand: Jabiru Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands