Motorola APX8500 Manual Download | Manualshive

Page: 203 / 273

background image

ADVANCED FEATURES

Full location coordinates

•

PTT ID (optional)

•

Longitude and latitude

•

Relative distance or direction

Short location coordinates

•

PTT ID (optional)

•

Longitude and latitude

Note:

If the transmitting radio is stale at the location

after a period, the receiving radio display shows the
last known location. If the transmitting radio does not
have GPS or the receiving radio could not decode
the GPS signal of the received signal, the receiving
radio display shows the location as unknown.

Global Positioning System/Global Navigation Satellite System

Peer-Location on the Display (ASTRO

®

25 Conventional)

203

This feature is only available for radio-to-radio voice
transmissions, dispatch call and selective call.

Both the transmitting radio and receiving radio must
be configured to enable them to send and receive
the GPS coordinates.

Note:

If the receiving radio is operating in a Mixed

Mode channel, only if its voice transmission is
through conventional ASTRO

®

25 system then the

radio can receive the location coordinates of the
peers.

This feature is also operable in a Scan Active
channel or Scan Talkback channel.

After receiving a voice transmission with GPS
coordinates enabled on the receiving radio, the
display shows the coordinates available in full or in
short coordinates.

«
...
201
202
203
204
205
...
»

Summary of Contents for APX8500


















































































































































































































































































Reviews:

No comments

Related manuals for APX8500

Brand: Raymarine Pages: 108

Brand: Raymarine Pages: 3

Brand: i-box Pages: 18

Brand: Xoro Pages: 32

Brand: Vertex Standard Pages: 34

Brand: Grundig Pages: 10

Brand: Radio Shack Pages: 24

Brand: PRESIDENT Pages: 44

Brand: Hitachi Pages: 12

Brand: Hitachi Pages: 20

Brand: Hitachi Pages: 20

Brand: Hitachi Pages: 24

Brand: Hitachi Pages: 28

Brand: Hitachi Pages: 18

Brand: Hitachi Pages: 10

Brand: Hitachi Pages: 28

Brand: Hitachi Pages: 32

Brand: Hitachi Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands