manualshive.com logo in svg

Motorola 56F8323, User Manual

Share
Download
Motorola 56F8323 User Manual Download Page 33

Serial 10-bit 4-channel D/A Converter (Optional)

MOTOROLA

Technical Summary

2-17

2.10   Serial 10-bit 4-channel D/A Converter (Optional)

The 56F8323EVM board contains the provions for a user to provide a serial 10-bit, 
4-channel D/A converter connected to the 56F8323’s SPI #0 port. The output pins are 
uncommitted and are connected to a 4x2 header, J4, to allow easy user connections. Refer 
to 

Figure 2-8

 for the D/A connections and 

Table 2-11

 for the header’s pin-out. The D/A’s 

output full-scale range value can be set to a value from +0.0V to +2.4V by a trimpot, R48. 
If this trimpot is preset to +2.05V, it would provide approxi2mV per step. If 
another device must be used with SPI #0’s MISO signal and with the D/A converter on the 
board, the daisy chain jumper, JG9, can be used to extend or isolate the serial chain.

Figure 2-8.   Serial 10-bit, 4-Channel D/A Converter

Table 2-11.   D/A Header Description

J4

Pin #

Signal

Pin #

Signal

1

D/A Channel 0

2

AGND

3

D/A Channel 1

4

AGND

5

D/A Channel 2

6

AGND

7

D/A Channel 3

8

AGND

1

3

5

7

2

4

6

8

D/A Connector

D/A 0

D/A 1

D/A 2

D/A 3

+3.3VA

R48

V

REF

MAX5251

DIN

DOUT

SCLK

CS

CL

MOSI0

1

2

MISO0

SCLK0

SS0

JG9

56F8323

RSTO

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for 56F8323





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands