manualshive.com logo in svg

Motorola 56F8323, User Manual

Share
Download
Motorola 56F8323 User Manual Download Page 27

Power Supply

MOTOROLA

Technical Summary

2-11

2.7   Reset

Logic is provided on the 56F8323 to generate an internal Power-On RESET. Additional 
reset logic is provided to support the RESET signals from the JTAG connector, the 
Parallel JTAG Interface and the user RESET push-button, S1; refer to 

Figure 2-6

. 

Figure 2-6.   Schematic Diagram of the RESET Interface

2.8   Power Supply

The main power input to the 56F8323EVM, +12V DC at 1.2A, is through a 2.1mm coax 
power jack. This input power is rectified to provide a DC supply input. This allows a user 
the option to use a +12V AC power supply. A 1.2Amp power supply is provided with the 
56F8323EVM; however, less than 500mA is required by the EVM. The remaining current 
is available for custom control applications when connected to the Daughter Card 
connectors. The 56F8323EVM pr5.0V DC regulation for the CAN interface and 
additional regulators. The 56F8323EVM pr3.3V DC voltage regulation for the 
processor, memory, D/A, ADC, parallel JTAG interface and supporting logic; refer to 

Figure 2-7

. Additional voltage regulation logic provides a low noise +3.0V DC voltage 

reference to the controller’s A/D V

REFH

. Optionally, the processor’s A/D V

REFH

 voltage 

can be provided by the +3.3VA supply on the board by removing U15 and adding a 10 
ohm resistor at R83. A jumper, JG11, and resistor, R68, are provided to allow the analog 
and digital grounds to be isolated on the 56F8323EVM board. This allows the analog 
ground reference point to be provided on a custom board attached to the 56F8323EVM’s 
Daughter Card connectors. By removing R68, the AGND reference is disconnected from 
the 56F8323EVM’s digital ground. By placing a jumper in JG11 or by reinstalling R68, 
the AGND is reconnected to the 56F8323EVM’s digital ground. Power applied to the 
56F8323EVM is indicated with a Power-On LED, referenced as LED13. Optionally, the 
user can provide the +2.5 DC voltage needed by the controller’s core on connector J14 and 
disable the on-chip CORE voltage regulator by removing the jumper on JG12. 

RESET

PUSHBUTTON

MANUAL RESET

JTAG_TAP_RESET

JTAG_RESET

RESET

TRST

S1

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for 56F8323





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands