6A
6B
EN
EN
07. PROGRAMMING
CODE PGM
WIRELESS SENSOR - WITH ACCESS TO CONTROL BOARD
REMOTE CONTROL - WITHOUT ACCESS TO CONTROL BOARD
07. PROGRAMMING
WIRELESS SENSOR - WITHOUT ACCESS TO CONTROL BOARD
The control unit is supplied by the manufacturer with PGM function active.
For disable press the SET button continuously for 5 seconds and then there is the alternating flashing of
the LED T. MOT, now has 30 seconds to activate or deactivate the PGM. With the SEL button position the
flashing of the LED CODE and the SET button to enable or disable the PGM function. After 30 seconds, the
control board returns to the main menu.
Return to deactivate the LED TEST that in case of emergency, close the awning in its entirety.
If the LED TEST stay on, the awning only will close during 5 seconds. When the awning close
by order of sensor, we can see what the order is to be sent, checking that the LED of the
sensor is on within the monitor.
For more information
on how to adjust the wind speed, sensitivity and illuminance sensor,
read the manual of sensor Wiweather.
To reset the sensor, simultaneously press the SEL and SET buttons of sensor for 2 seconds.
LEDs light on and all the sensor back to the factory programming.
If you want to memorize a wireless sensor, follow these steps:
01 •
Power the sensor.
02 •
Open the memory of the control board MC7 and position with the SEL button flashing LED CDM.
03 •
After opening the memory of control board, has 30 seconds to send the order of sensor to control
board. Position to LED CODE with the SEL button of sensor and will flashing.
04 •
Immediately press the SET button of sensor so that it emits a rapid flashing of the LED CODE.
05 •
With the SEL button sensor must now select the
functions you want to leave assets in sensor the sun/ wind / rain. Press SEL repeatedly until the desired
function LED flashes. With the LED flashing, press the SET button for more than second until it is fixed
LED lit active function.
To disable any function, repeat point but press the SET button at least second and the LED goes out,
leaving the function disabled.
Programming the wireless sensor without access to control board is carried out as follows:
01 •
Press continuously, for a longer time than seconds, the opening channel of a previously stored
remote control.
02 •
With the sensor SEL, position the LED CODE will begin to flash this, and immediately press for
more than 3 seconds the sensor SET button to this issue a quick flashing of the LED CODE.
At this point you are informed of the success of programming signaled by opening and closing for 1 sec
of awning.
The control board allows the programming of another remote control, without intervening directly on
the control panel SEL key, performing a remote operation. Programming a code for a remote control is
as follows:
01 •
Press and hold the opening channel of a previously stored radio remote control for longer than 10
seconds.
02 •
At the same time the control panel enters programming mode. Press for 3 seconds the closing
channel of the new command..
03 •
Press the opening channel for another 3 seconds.
The motor will signal reception of the control with an opening for 1 sec and closing for 1 sec. The
command is now programmed. If you want the same button to open and close memorize only the first
button and wait 30 sec to exit remote programming.
LED
OFF
ON
CODE
PGM distance = ON
PGM distance = OFF
T. MOT
Intermittent ON/OFF
To test the sensor should follow the next instructions:
01 •
With the SEL button position the LED TEST will begin to flash this. Press the SET button for more than
second and the LED stays on.
02 • TEST RAIN SENSOR
Pass a wet finger over the sensor until the awning begins to close the awning will
close during 5 seconds.
03 • TEST WIND SENSOR
Turn the propeller. The awning will close for 5 seconds.
04 • TEST SUN SENSOR
Turn VR clo and the awning will open for 5 seconds. Turn the VR
anticlockwise and the awning will close for 5 seconds.
If the awning perform the indicated operations successfully, the sensor is programmed and the test
finished.
The control board allows memorize only Sensor Wireless. Programming a new Wireless
Sensor annuls definitely the previously memorized code.
