background image

Toto Entrada and Promenade II Installation Guide

4

ENGLISH

BEFORE INSTALLATION

 

„

Read these instructions thoroughly before beginning work.

 

„

 Please leave instructions for customers.  These instruction contain maintenance 

and warranty information.

 

„

If necessary, remove the existing toilet.

For  your  new  TOTO  toilet  to  fit  correctly,  the  rough-in,  the  distance  between  the 

finished wall to the center of the 

closet flange, must be at least 

12 inches for most models.  

NOTE:  Models  with  10” 

rough-in have model numbers 

ending with “.10”, for example 

C744EF.10.

Supply 

Valve

Finished Wall

"RI"

C/L

Closet 

Flange

IMPORTANT!

 

Due to the powerful performance of our Cyclone, G-Max, E-Max and Power Gravity 

flushing  systems,  they  are  not  specified  for  back-to-back  installations.  The  only 

means of installing these toilets in a back-to-back situation is when the toilet drain 

connections incorporate a WYE fitting. Please contact your builder or contractor prior 

to this installation.

Double Combination WYE / 1/8 Bend

YES

Double Sanitary Tee / Sanitary Cross

NO

INSTALLATION PROCEDURE

Ill. 1

Ill. 2

W

ax Ring

Horn

Bolt Cap

Nut *

Washer *

Base Cap

Bowl Base

Three Points of Contact

* Not Supplie

d

Ill. 3

1) Clean any debris out of the closet flange 

and then install new mounting bolts 

(not supplied) into the slots of the closet 

flange (see Illustration 1). The head of the 

bolt should be inserted into the slot with 

its threads facing upward.

2) Carefully turn the toilet upside down 

onto some padding. Firmly press a new 

bowl wax ring (not supplied) onto the 

circular recess around the toilet bowl’s 

horn (see Illustration 2). Turn the toilet 

upright and gently lower into position 

over the closet flange. With toilet 

properly aligned, press firmly on both 

sides of toilet rim to set the bowl wax 

ring (see Illustration 3).

CAUTION: 

Do not move the bowl after 

the bowl wax ring is set. Thread the nuts 

and tighten evenly until bowl is snug to 

closet flange. Install the bolt caps (see 

Illustration 3).

CAUTION: 

Do not over-tighten the nuts

as damage to the china bowl may result.

3

ENGLISH

TABLE OF CONTENTS

THANKS FOR CHOOSING TOTO! 

The mission of TOTO is to provide the world with healthy, hygienic and more 
comfortable lifestyles. We design every product with the balance of form and function 
as a guiding principle. Congratulations on your choice.

Thanks for Choosing TOTO

®

! ........................................................................................... 3

Before Installation ............................................................................................................... 3
Common Tools Needed .................................................................................................... 3
Included Parts ..................................................................................................................... 3
Before Installation ............................................................................................................... 4
Installation Procedure ........................................................................................................ 4
Maintenance Instructions ................................................................................................... 7
Care and Cleaning .............................................................................................................. 9
Warranty ............................................................................................................................ 10
Rough-In Dimensions  ...................................................................................................... 28 
Replacement Parts ............................................................................................................ 29

Check to make sure you have all these parts from the package:

COMMON TOOLS NEEDED

China Bowl with Lid

Tank

c

d

Tank Lid

Tank to Bowl Gasket

 

a. Bolts (metal) - 2
b. Washers (rubber) -2 

c. Washers (metal) - 4
d. Nuts (metal) -4

•  10” adjustable wrench
•  Carpenter’s Level
•  Hacksaw
•  Tape Measure

•  Hand Pliers
•  Flat Screwdriver
•  Putty Knife

ADDITIONAL ITEMS (NOT SUPPLIED BY TOTO):

•  Bowl Wax Ring
•  Closet Flange Mounting Bolts

    (usually 2 T-bolts, 2 metal washers and 2 nuts)

•  Water Supply Line
    (typically 1/2” compression to 7/8” ballcock)
•  Toilet Seat (TOTO SoftClose recommended)

f

a. Caps (plastic) - 2 b. Base (plastic) - 2

INCLUDED PARTS

5

ENGLISH

INSTALLATION PROCEDURE

NO

NO

YES

Ill. 6

Ill. 4

Ill. 5

Tank to Bowl 

Gasket

1

3

2

Fill 

Valve Nut

Flush 

Valve Nut

Metal Washer

Nut

Rubber Washer

Bolt

Cut Away View

3

1 & 2

3 Gap

1 & 2

3

1 & 2 

Gap

Points of Contact

NOTE: 

Three Points of Contact:

The toilet bowl has three points o 
contact, which will actually contact the 
bottom of the toilet tank when properly 
installed. The location of these points 
can be seen on the bowl at the tank 
receiving area. The three points are front 
left (1), front right (2), and back center 
(3). Recall these three points during the 
Toilet Tank installation.

3) Place the tank upside down onto some 

padding. Inspect the smaller fill valve 

nut and larger flush valve nut for a 
secure connection (see Illustration 4). 
Try to tighten the nuts with your hands. 
If loose, tighten the nut hand tight and 

an additional 1/4 turn for the smaller fill 

valve nut and an additional 1/2 turn for 
the larger flush valve nut.

     Place the tank-to-bowl gasket onto the 

flush valve nut. While pressing down, 
spread the gasket over the nut until the 
gasket touches the bottom of the tank. 
A slight gap between the tank bottom 
and the gasket is allowable.

4) Lay the tank down on its back. Place a 

rubber washer onto a brass bolt (see 
Illustration 5). Reach inside the tank 
and position the bolt through one of 
the holes in the bottom of the tank. 
On the outside of the tank, place a 
metal washer and nut onto the bolt. 

Hold the bolt centered in the hole and 
tighten the nut finger tight. Turn the nut 

an additional 1/2 turn with a wrench. 
Repeat this process for the remaining 
hole in the tank.

      Pick up the tank and carefully guide 

the brass bolts to align the tank with 
the bowl. Attach a metal washer and 

nut to each bolt. Tighten the nuts finger 

tight and inspect that the tank is level 
(see Illustration 6). Once level, tighten 
the bolts equally until the tank makes 

THREE POINTS OF CONTACT with the 

bowl.

Tools Needed:

6

ENGLISH

INSTALLATION PROCEDURE


7/8” Ballcock Th

read

HAND TIGHTEN ON

LY

 

Ill. 7

Ill. 8

Seat

 

Hinge

Cap

Plastic
Bolt

Seat

 

Stopper

Bowl

Plastic Nut

1 - Cap
2 - Plastic Bolt

3 - Seat Hinge
4 - Seat Stopper

5 - Toilet Bowl
6 - Plastic Nut

MOUNTING HARDW

ARE

5) Flush the water supply line for a few seconds 

to remove any debris that may enter the 

new fill valve. (For new home constructions 

and/or additions, flush the water supply line 
for more than a minute to help remove any 

residual PVC adhesives, solder flux, and/ or 

pipe sealants that were used for the new 
plumbing.) Connect the water supply line to 

the fill valve threads as seen at the bottom 

of toilet tank (see Illustration 7). Tighten this 

connection finger tight.

CAUTION: 

Avoid using a wrench to tighten 

the connection as you may damage the 

plastic threads and/or cause the fill valve to 

rotate inside the tank.

NOTE: 

The water supply pressure should be 

20 to 80 psi static.

6) No ballcock / fill valve adjustments are 

needed. The water will automatically stop at 

proper level. Flush the toilet several times. 

Check flapper valve for proper operation. 
Make sure that chain is not tangled and that 
the flapper arm is in its proper position.

7) Install the toilet tank lid onto the toilet tank 

top.

8) Install the toilet seat onto the toilet bowl 

using the mounting hardware in the toilet 

seat box. Place seat onto bowl and rotate 

the hinge down. Position seat stoppers 
under the seat hinge. Insert bolt into seat 
hinge and through the toilet bowl. Install 
plastic nut onto bolt from underneath. 
Tighten the bolt securely. Install the seat 
bolt caps.

NOTE: 

Tighten the seat bolt until the hinge is 

secure. The seat and lid will have slight side 
to side movement, which is normal. This 
freedom of movement allows the seat to 

SoftClose® without binding. 

5

ENGLISH

INSTALLATION PROCEDURE

NO

NO

YES

Ill. 6

Ill. 4

Ill. 5

Tank to Bowl 

Gasket

1

3

2

Fill 

Valve Nut

Flush 

Valve Nut

Metal Washer

Nut

Rubber Washer

Bolt

Cut Away View

3

1 & 2

3 Gap

1 & 2

3

1 & 2 

Gap

Points of Contact

NOTE: 

Three Points of Contact:

The toilet bowl has three points o 
contact, which will actually contact the 
bottom of the toilet tank when properly 
installed. The location of these points 
can be seen on the bowl at the tank 
receiving area. The three points are front 
left (1), front right (2), and back center 
(3). Recall these three points during the 
Toilet Tank installation.

3) Place the tank upside down onto some 

padding. Inspect the smaller fill valve 

nut and larger flush valve nut for a 
secure connection (see Illustration 4). 
Try to tighten the nuts with your hands. 
If loose, tighten the nut hand tight and 

an additional 1/4 turn for the smaller fill 

valve nut and an additional 1/2 turn for 
the larger flush valve nut.

     Place the tank-to-bowl gasket onto the 

flush valve nut. While pressing down, 
spread the gasket over the nut until the 
gasket touches the bottom of the tank. 
A slight gap between the tank bottom 
and the gasket is allowable.

4) Lay the tank down on its back. Place a 

rubber washer onto a brass bolt (see 
Illustration 5). Reach inside the tank 
and position the bolt through one of 
the holes in the bottom of the tank. 
On the outside of the tank, place a 
metal washer and nut onto the bolt. 

Hold the bolt centered in the hole and 
tighten the nut finger tight. Turn the nut 

an additional 1/2 turn with a wrench. 
Repeat this process for the remaining 
hole in the tank.

      Pick up the tank and carefully guide 

the brass bolts to align the tank with 
the bowl. Attach a metal washer and 

nut to each bolt. Tighten the nuts finger 

tight and inspect that the tank is level 
(see Illustration 6). Once level, tighten 
the bolts equally until the tank makes 

THREE POINTS OF CONTACT with the 

bowl.

WARNING!

 Do not use 

in-tank bowl cleaners.
The use of high 
concentration of chlorine 
or chlorine-related 
products can seriously 
damage fittings in the 
tank. This damage can 
cause leakage and 
property damage. TOTO 
shall not be responsible 
or liable for any tank 
fitting failure or damage 
caused by the use of in-
tank bowl cleaners.

Summary of Contents for Kohler Cimarron










Reviews: