Mortch TANCO User Manual Download Page 16 | Manualshive

Page: 16 / 22

background image

①

Remove the oil dipstick.

②

Remove the oil plug for displacement to drain the

used oil.

③

Reinstall the oil plug for displacement, paying

attention to be tightened .

④

Refill

0.8 L recommended fresh engine oil.

⑤

Fasten all the nuts and screws.

7. Brake system

Normal free travel of the brake lever is about 10-20mm.

①

The front brake (disk brake)

②

The rear brake (drum brake)
Turn the adjusting nut to get a proper travel.

Adjusting nut

Warning

◆

FREE TRAVEL means the distance between
the positions from free status to the
beginning performance of the brake.

◆

Pay attention to the sensitivity of the brake.

MORTCH INTERNATIONAL LIMITED

<15>

http://www.mortch.com

«
...
14
15
16
17
18
...
»

Summary of Contents for TANCO























Reviews:

No comments

Related manuals for TANCO

Brand: Triumph Pages: 18

Brand: Rascal Pages: 36

PERFORMANCE Series

Brand: Qwic Pages: 144

Brand: N-Zeta Pages: 53

Brand: WISPEED Pages: 71

Brand: Hover-1 Pages: 27

Brand: Zizito Pages: 48

Brand: Orthoquad Pages: 15

Brand: Vermeiren Pages: 32

Brand: Vermeiren Pages: 60

Brand: X-TREME Pages: 22

Brand: Pride Pages: 47

URBANEASE Series

Brand: VANPOWERS Pages: 61

Brand: Karma Pages: 32

Brand: Zhuhai Shuangye Electronic Technology Pages: 4

Brand: Olsson and Brothers Pages: 48

Brand: Jetson Pages: 24

Adventure 2.0 2022

Brand: Jetson Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands