background image

The Specialist In Drum Handling Equipment

MODEL 85AM

Drum Karrier with Spark Resistant Parts

Operator’s Manual for Morse Model 85AM Drum Karrier with Spark Resistant Parts

Serial number 1114 to 0515 (MMYY)

morsedrum.com

Copyright 2015  -  Morse Mfg. Co., Inc. 

 

Form PL85AM  (1114-0515)  

(Updated April 29, 2015 1:16 PM)

               

3

Machine Description

Model 85AM 

Drum Karrier is designed to lift, transport and dispense a standard 55-gallon 

steel drum 22.5” in diameter. The maximum capacity is 800 Lb.

Important

Review the Material Safety Data Sheet(s) for the material(s) in the drum(s) and take 

1. 

all  necessary  precautions.  Safety  shoes,  work  gloves,  hard  hat  and  other  personal 

protective devices are recommended.

Please read all instructions thoroughly before attempting to operate your new Morse drum handler.

2. 

The 85 Series Drum Karriers have a maximum capacity rating of 800 Lb. for a FULL drum and 500 Lb. for a HALF-FULL drum, and 

3. 

are designed to lift and move a drum of the size and type noted above. DO NOT exceed this rating. Exceeding this rating or handling 

drums other than those mentioned above is unsafe and could result in equipment damage, excessive wear, awkward or dangerous 

handling.

When loading, unloading, operating, or maintaining your MORSE drum handler, always use care and good judgment.  Maintain secure 

4. 

footing and a firm hold.  Keep hands and loose clothing away from all moving parts. Never allow anyone to be below any part of a raised 

drum handler or drum. Read operating instructions and review the pictures in the sales brochure before operation.

The 85 Series are a “Group 1 structural and mechanical” below-the-hook lifting device which are covered by the American National 

5. 

Standard ASME B30.20. The user should comply with all aspects of this standard.

Operating Instructions

Start  with  Drum  Karrier  on  the  floor.  Lower  hoist  and 

1. 

engage hoist hook to lift Drum Karrier.

Raise hoist to lift Drum Karrier clear of floor and transport 

2. 

it to the drum.

Suspend  Drum  Karrier  at  a  height  which  aligns  drum 

3. 

saddle with center of drum.

With Cinch Chain (item 103) hanging freely, push Drum 

4. 

Karrier  against drum so that saddle will encircle drum.

Secure the drum: drape the Cinch Chain (item 103) across 

5. 

the face of the drum and engage a link in notch in hub of 

ratchet (shown right). Pull up on ratchet handle to tighten 

chain. If the chain doesn’t cinch tightly on the drum, lift the 

pawl  (item105)  to  loosen  and  release  the  chain  and  try 

again with a different link in the notch. Firm hand pressure 

on the ratchet handle should tighten the chain sufficiently 

to hold the drum. DO NOT use mechanical aids such as a 

pipe to extend handle for extra leverage.

Either one of the two spring loaded plunger tilt-locks may 

6. 

be locked to hold the drum upright. It is not necessary to 

lock both of them.

Raise hoist and position drum at pouring station.

7. 

Before unlocking the tilt-lock(s) to permit tilting the drum, it is recommended that you steady the drum and be prepared for its possible 

8. 

tendency to tilt toward its heavier side.

With tilt-locks unlocked, manually tilt the drum for pouring. The drum pouring angle may be varied or it can be locked in horizontal 

9. 

position by one of the tilt-locks.

After emptying, rotate drum back to vertical position and lower hoist to return the empty drum.

10. 

To remove drum: Pull ratchet handle to relieve pressure on ratchet teeth. Lift pawl handle (item 105) to release teeth engagement and 

11. 

rotate ratchet to loosen chain and allow its removal from notch.

Maintenance

Lubricate ratchet, pawl, tilt locks, fulcrum shafts and other moving parts periodically to maintain free action and reduce wear.

1. 

Periodically inspect all moving parts, framework and contact areas for signs of wear, fatigue or loosening. Tighten, adjust or replace 

2. 

parts as necessary to prevent failure and maintain proper function.

Summary of Contents for 85AM






Reviews: