background image

The Specialist In Drum Handling Equipment

Model 285XBP

Super-Duty Battery Powered Forklift-Karrier

operator’s Manual for Morse Super-Duty Forklift-Karrier with Battery Powered Drum tilt 

Model 285XBP with Serial number 1017 to ____ (MMYY)

morsedrum.com

Copyright 2020  -  Morse Mfg. Co., Inc. 

 

Form PL285XBP (1017-____) 

 

(Updated 27 Apr, 2020) 

4

operating Instructions

Before sliding forklift forks into the fork tubes, adjust forks to 

1. 

an inside spread of 24.5” (62.2 cm) minimum. Lock forks into 

position on the forklift carriage.

Drive the forklift forward to slip the forks into the fork tubes. 

2. 

Hook the safety chain clamp to top edge of carriage and 

tighten T-bolt. Take up slack by engaging a chain link in 

the provided notch. Transport Forklift Karrier to drum to be 

handled.

Drive the forklift with the Forklift Karrier near floor level to 

3. 

position the saddle band around the middle of the drum 

between the ribs.

Open the toggle clamp by activating the release lever (item 

4. 

108) and swing both hinge bands to the open position. Push 

the Forklift-Karrier against the drum to surround the drum with 

the saddle band.

Close the two hinged bands around the drum and latch the 

5. 

toggle clamp to secure the drum.

Remove pendant assembly (item # 12) from holder on guard 

6. 

and place near operator’s seat.

Raise forks to clear the floor and transport drum in vertical 

7. 

position to dispensing location.

To pour drum: press the down button on the pendant, rotating 

8. 

drum to angle required for dispensing.  

When dispensing is completed, rotate the drum back to 

9. 

vertical by pressing the up button on the pendant and return 

drum. While transporting, ensure that the drum is raised away 

from the floor to prevent the drum bottom from interfering with 

a pallet or other obstacle.

CAUtIon: 

Do not exceed weight capacity 

of 2500 Lb. (1134 kg) for FULL drum, 1250 Lb.  

(567 kg) for HALF-FULL drum.

CAUtIon: 

Do not allow drum to impact on 

floor, ground, or dumping station, etc.

Maintenance

Lubricate cylinder pins (items 13 and 28) and linkages (items 

1. 

3 and 7).

Clean and oil saddle hinge, and other moving parts 

2. 

periodically.  (Clean & lubricate more often in environments 

where dust, dirt or other foreign particles will effect the 

performance of moving parts.)

Periodic inspection for the general condition of structural and mechanical components is imperative for safe and efficient operation.

3. 

Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening.  Tighten, adjust, or 

4. 

replace parts as necessary to prevent failure and maintain proper function.

Inspect the hydraulic system for oil drips, hose damage, or other signs of wear.  Inspect the level and condition of the hydraulic fluid.  

5. 

Replace any parts that show signs of wear.

Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.

6. 

Hydraulic pump is shipped filled with Noco Premium plus automatic transmission fluid d/m. Material safety data sheet (msds) is 

7. 

available online. Change oil yearly, sooner depending on dirty conditions or outdoor use. Replace oil with Mobil dte 24 or equivalent 

for indoor use (Mobil dte 13 for outdoor use).

toggle Clamp

Summary of Contents for 285XBP









Reviews: