manualshive.com logo in svg

Morphy Richards TURBO STEAM IRON, Instructions Manual, Page: 5 / 8

Share
Download
Morphy Richards TURBO STEAM IRON Instructions Manual Download Page 5

This is perfectly normal as it shows that

the iron is maintaining the heat setting you
have chosen.

It is always a good idea to begin with

cool fabrics and work up to higher settings.

An iron heats up quicker than it cools

down so you’ll save time and electricity.

Features of your iron

Temperature indicator light

The indicator light under the control

knob shows that the iron is warming up.
When the required temperature is reached
the light will go out and will cycle on-off
during operation.

Dry ironing

You can use your iron as a dry iron only.

Make sure the variable steam control 

‹

is

set to the ‘0’ symbol.

Any temperature setting may be used

depending on the garment. The spray
feature may be used provided there is water
in the tank (see filling section). You do not
need to put any water in the tank when dry
ironing only.

Spray

Press the spray

button 

¤

and aim the

spray of water at
stubborn creases. You
can do this whilst dry
ironing providing there
is water in the tank.
When using the water spray it may be
necessary to push the button a few times to
get the spray pump primed.

Variable steam

Fill the iron with water as described in

‘Filling’, page 4 and insert the plug into the
electrical socket.

The steam output can be varied from

low to high by sliding the variable steam
control 

C

. When using the iron at the

bottom of the steam range, the steam
output should be adjusted to the lowest
setting.

The steam facility should only be used

on garments which are suitable for ironing
at 2 and 3 dot setting.

Shot of steam

Press the shot of steam

button 

⁄

to obtain a burst

of extra steam for ironing
out creases in heavy
material such as denim etc.

The shot of steam can

be used whilst dry ironing,
providing there is water in
the tank, and the
temperature control is set within the steam
range.

Do not use shot of steam at

temperatures below the steam range shown
on the control.

Note: For optimum steam quality, do not

operate the shot more than three times in
succession.

Vertical steam

Hold the iron in a vertical position

between 1cm and 2cm away from the item

D

. Press the shot of steam button 

⁄

, this

will create vertical steam. This feature is
especially useful for removing creases from
hanging clothes, curtains, wall hangings,
etc.

Note; For optimum steam quality, do not

operate the shot more than three times in
succession. 

5

lower steam

higher steam

C

D

turbo steam RN40655 Rev 1  23/7/04  1:34 PM  Page 5

Summary of Contents for TURBO STEAM IRON









Reviews:

No comments