Morphy Richards Supervac gold Instructions Manual Download Page 8

8

The guarantee may be invalidated if the motor
is damaged due to: using the appliance
without the filter(s) installed; not cleaning the
filter(s); not replacing a damaged filter; not
clearing any blockages.

WARNING: Always remove the mains adaptor

(23)

from the mains supply before undertaking

any maintenance or cleaning procedures.

Your cleaner is manufactured to withstand normal
day-to-day use, but occasionally wipe over with a
damp cloth to help maintain its good looks. Take
care not to get the electrical connections wet.

Abrasive cleaners should not be used.

Empty the dust canister

(10)

regularly even if it

does not look full, this will maintain the
performance.

To ensure optimum suction and performance, we
recommend that the canister is only filled to the
line shown on the side of the canister.

We recommend cleaning the foam filter

(8) 

and

dust canister filter

(9) 

and checking for any

blockages every time the dust canister

(10) 

is

emptied.

1.

Disconnect the extension tube

(14)

from the

handheld vacuum cleaner 

(6)

.

2.

Holding the handheld vacuum cleaner in one
hand (whilst simultaneously pressing the dust
canister release button

(5)

with your thumb),

firmly hold the bottom of the dust canister

(10)

with your other hand and pull the dust canister
away from handheld vacuum cleaner.

3.

Holding the dust canister

(10)

over a dustbin,

press the dust canister swing base release button

(11)

down to release the swing base

(16)

, allowing

it to swing open and empty the dirt. After the dirt
has been emptied swing the base closed and
press until it clips shut.

Maintenance

Maintenance - emptying
the dust canister and
cleaning the filters

Press 

button 

here

Hold 

firmly 

here

Pull

24

25

Using the attachments

Crevice tool and brushes

Dusting brush (24)

for carpet, upholstery and stairs etc.

Upholstery nozzle (24)

for upholstery and bedding etc.

Slide the dusting brush back by clicking the button on
the attachment - this reveals the upholstery nozzle.

Crevice tool (25)

for awkward places, corners and

behind radiators etc. This tool is also useful on stairs.

VC731011MUK Rev1.qxp_Instruction Book  05/03/2020  10:44  Page 8

Summary of Contents for Supervac gold













Reviews: