background image

5

the tank. When using the water spray it may be
necessary to push the button a few times to get
the spray pump primed.

Steam ironing

Ensure that the temperature

control dial is set in the steam
range 

C

and that there is

water in the tank.

Rest the iron on its heel and

allow to heat up.

Before you start ironing,

slide the steam button up, to
the steam position 

E

.

If you need to refill the

water tank during use, unplug
the iron and follow the filling
instructions taking care not to
spill any water over the iron.

Variable steam (certain
models only)

If your iron is fitted with variable steam, the

steam output can be varied from low to high.
Simply slide the variable steam button up or
down 

F

.

The high position is for ironing
stubborn creases

The mid position is for normal
ironing

The low position switches the
steam off.

Shot of steam ironing
(certain models only)

Press the shot of steam

button 

G

to obtain a burst of

extra steam for ironing out
creases in heavy material such as
denim etc. The shot of steam
can be used whilst dry ironing,
providing there is water in the
tank and the temperature
control is set in the steam range.
Do not use shot of steam at
temperatures below the steam
range shown on the control.

Vertical steam facility (certain models
only) 

Hold the iron in a vertical position between

1cm to 2cm away from the item 

H

. Press the

shot of steam button 

G

, this will create vertical

steam. This feature is especially useful for
removing creases from hanging clothes, curtains,
wall hangings, etc.

Auto shut-off (certain models only) 

If your iron is an ‘auto shut-off’ model it will

automatically turn your iron off within 60
seconds of not being used. Grasping the iron by
its handle will turn it on again. If the iron is below
the temperature set on the temperature control
dial, the temperature indicator light will illuminate
until the iron reaches the set temperature.

AUTO SHUT-OFF IS NOT AN

ALTERNATIVE TO UNPLUGGING THE
IRON WHEN NOT IN USE.

E

G

H

D

Steam spray irons

Steam spray shot irons

F

Steam on

Steam off

High steam

Low steam

Steam off

Summary of Contents for IB42700







Reviews: