Thank you for buying your new Morphy Richards male
grooming system. Please read these instructions
carefully before use and keep in a safe place for future
reference.
Key features
A
Cutting blades
B
Standard comb
C
On/off switch
D
Charging adaptor
E
LED charging indicator
F
Recharging base
G
Cleaning brush
H
Lubricating oil
I
5 Moustache comb
J
Styling comb
Ni-cad batteries
Push down the battery door to open and then take
out the Ni-cad batteries.
Your beard trimmer is operated
by 2 x AA rechargeable
batteries. Ensure the batteries
are correctly fitted. Refit
battery door.
USE ONLY NICAD RECHARGEABLE BATTERIES in
order to avoid damage.
Batteries are not covered by the 2 year guarantee.
In the interest of environmental safety, dispose
of batteries safely.
Operating your trimmer
1
Push the on/off switch upward to operate and down
to turn off the trimmer.
Before using the trimmer charge the unit overnight.
Make sure the LED indicator is on showing correct
charging.
To Recharge
1
Use only the adaptor (charger) provided.
2
Charge takes 8 hours.
3
Connect plug to trimmer and plug adaptor into the
electrical socket.
4
When charging, RED LED indicator will light up
showing correct recharging.
Attachment comb (trimming guide)
Your beard trimmer provides 2 attachment combs.
Styling Comb
- provides 5 settings of cutting length
9, 11, 13, 15 and 17mm.
Standard comb
- provides 5 settings of cutting length
1.5, 3, 4.5, 6 and 7.5mm.
Trim against the direction of the hair growth.
Start at a longer setting (15mm or 17mm) to prevent
accidentally trimming hair too short.
As you become familiar with the setting, adjust the
guide to the desired trimming length.
To trim beards
1
Comb hair outward so they are at a
maximum height and in the same
direction.
2
With the trimming guide in place,
set the guide to the desired
setting.
3
Slide the On/off switch to the on
position and begin trimming. (figure 1)
To trim outer edge of beard
and add definition
1
Remove trimming guide (figure 2)
and hold the trimmer diagonally
with the front of trimmer facing
away from you.
2
Start at the chin and move back
towards the ear. (figure 3) Follow
the jawbone to cut away longer
hairs on the outer edge of the
beard.
To define the beard line
1
Hold the trimmer vertically with the
front of the trimmer facing you.
2
Start with the trimmed edge of the beard and with
a downward motion trim the area directly under the
beard line.
To thin and taper beard
1
Use the moustache comb to hold hairs in place
while trimming.
2
Hold the trimmer with front facing away from you.
Trim hair ends using an upward motion.
To trim moustache
(with trimming guide)
1
Ensure that the trimming guide is in place to avoid
over trimming the hair.
2
Comb hairs outward to the maximum height and in
the same direction.
3
Set the trimming guide to the desired setting.
4
Hold the trimmer vertically with the front facing
you and trim hairs using a downward motion
following the direction of your hair growth or you
may trim against your hair growth.
Without trimming guide
1
Place a finger on the upper lip only
to lift hair up, away from the skin.
Trim hairs using an upward motion.
2
After achieving desired length, use a
downward motion to blend
moustache hairs. (figure 4)
3
Hold trimmer perpendicular as
shown and move cutters sideways
to achieve the desired line above
the lip. (figure 5)
A
B
C
D
E
F
G
H
I
J
9
1.5
11
3
13
4.5
15
6
17
7.5
