Morphy Richards CYCLONIC BAGLESS VACUUM CLEANER - REV 4 Manual Download Page 1

w

www.morphyrichards.com

Cyclonic bagless vacuum cleaner

Please read and keep these instructions

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check

Dust canister

It is important to regularly empty the canister even if it does not appear full.  

Filters 

It is important that the pleated filter is shaken clean each time the dust canister is
emptied to allow air through the appliance. Wash the canister filters regularly in warm
water and allow to air dry. A spare pleated filter is included.

Blockages

Check the hose, tubes and tools for blockages

Safety cut-out

If the air-flow is bloked or the filters are not regulary cleaned a thermostat may operate. If
this happens, switch off and disconnect from the mains supply. Clear any blockage,
empty and clean the filters. Allow 60 minutes for the thermostat to reset.

Belt

Check and replace damaged or broken belt

Height adjustment

The height adjustment only comes into effect when the handle is released by the handle
release pedal 

È

.

VC73360MUK Rev 4

For replacement parts, help with using your Morphy Richards, problems
and lots more, contact us by phone or through our website.

U

UK

K  H

He

ellp

plliin

ne

e::  0

08

87

70

0  0

06

60

0  2

26

60

04

4  

R

Re

ep

plla

ac

ce

em

me

en

ntt  p

pa

arrtts

s::  0

08

87

70

0  1

16

67

7  6

66

63

35

5

IIrre

ella

an

nd

d  1

18

80

00

0  4

40

09

91

11

19

9

73360 rev4  11/7/06  14:43  Page 1

Summary of Contents for CYCLONIC BAGLESS VACUUM CLEANER - REV 4









Reviews: