6
Before use
Remove the protective cover from the soleplate (8).
Using the iron for steam ironing
1
Make sure the iron is not plugged in. Set the variable steam
switch (1) to ‘O’. Fill the water tank (10) via the filling hole (6). Fill
with the iron in a horizontal position to the MAX graphic on the
side of the water tank.
IN HARD WATER AREAS, WE RECOMMEND THE USE OF
DISTILLED OR DEMINERALISED WATER.
Never use battery topping up fluid or water containing any
substances like starch, sugar, fragrant additives or defrosted
water from a refrigerator.
NOTE: Please see point 2 of ‘Exclusions’.
2
Plug in the iron and switch on at the mains.
Set the temperature dial (9a) (certain models only) to the
temperature required (see ‘Temperature Guide’).
The temperature illumination in the dial will illuminate until the
required temperature is reached, then it will turn off.
Tip: We recommend the temperature indicator light is allowed to
illuminate and extinguish twice for the temperature to stabilise
before you begin ironing.
The temperature indicator light will switch on and off whilst you
are ironing, as the iron regulates the temperature.
Tip: Begin with cool fabrics and work up to higher settings. An
iron heats up quicker than it cools down so this will save you time
and energy.
3
Set the electronic temperature control panel (9b) (certain models
only) to the temperature required (see ‘Temperature Guide).
The iron will default to
(cotton) when the iron is plugged in.
Press the ‘SELECT’ button to toggle the temperature:
one press for MAX setting (linen);
two presses for
setting (nylon/silk);
three presses for
setting (wool/polyester);
four presses for
setting (cotton).
The appropriate light flashes until the temperature is reached, and
then the iron beeps.
For further information, see tips in step 2, above.
4
Vary the steam output using the variable steam switch (1), as
shown above.
4A
Only use the steam function on heavy fabrics and when the
temperature dial (9a) (certain models only) is set within the shaded
area,
4B
or the
or
or MAX setting is selected on the electronic
temperature control panel (9b) (certain models only).
Using the iron for steam ironing (continued)
5
For stubborn creases, use the water spray button (2).
If using for the first time, you may need to press this a few times
to prime the pump.
Steam boost
6
Press the steam boost trigger (3) for an extra steam burst for
stubborn creases / heavy fabrics.
NOTE: If you need to use the steam boost whilst dry ironing,
check the temperature is set within the steam range (see step 4).
NOTE: For optimum steam quality, do not operate the shot more
than three times in succession.
Features of your iron
Dry ironing
Your iron can be used for dry ironing. Set the variable steam
switch (1) to ‘O’ and set the temperature as desired (see
‘Temperature Guide’).
You won’t need water in the tank unless using the water spray or
steam boost features.
Vertical steam
7
Vertical steam is useful for removing creases from hanging
clothes, curtains, etc. Hold the iron between 1cm and 2cm away
from the item and press the steam boost trigger (3).
Anti-drip system (certain models only)
This prevents water escaping from the soleplate (8) when the iron
is too cold.
During use, the anti-drip system may emit a loud click, particularly
during heat-up or whilst cooling down. This is perfectly normal
and indicates that the system is functioning correctly.
Anti-scale system (certain models only)
This system reduces scale deposits and helps prolong the life of
the iron.
Auto shut-off (certain models only)
8
The iron will automatically shut down if stationary in the horizontal
position for 1 minute, or in the vertical position for 8 minutes.
When auto shut-off is activated, a beep will be heard and the
indicator light (4) will flash.
Gently move the iron and it will reheat. Wait for the iron to heat-up
and continue ironing.
Maintenance
To clean a coated soleplate
Do not use scouring powder or solution as this could cause
damage to the coating.
If any man-made fibres fuse to the soleplate (8), set the iron at the
MAX position and pass it over a clean piece of cotton to draw the
deposit off the surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp cloth and mild
detergent, then wipe dry.
Emptying and storing
9
When you have finished ironing, unplug and empty all water
from your iron and set the steam switch at the ‘O’ position.
When cool, store the iron on its heel with the cord wrapped
loosely around the heel.
NOTE: Please see point 3 of ‘Exclusions’
RN303100MEERev2A.qxp_MorphyRichardsInstructionBook04/11/201614:53Page6
All manuals and user guides at all-guides.com
all-guides.c
om
