Morningstar SureSine 1000 W Installation And Operation Manual Download Page 45 | Manualshive

Page: 45 / 66

background image

35

COMMUNICATION OPTIONS

MS-003650

(Rev 0 Draft 10)

4.1.2

SureSine Utility App

The SureSine inverter has a Utility App available for monitoring and settings
adjustments. This app is designed for Android and Apple devices and
connects using Bluetooth.

The SureSine Utility App is available at Google Play and Apple App stores.
Download and install the App and follow the instructions from the App for
set up and operation.

Figure 27: SureSine Utility App (Main Dashboard)

«
...
43
44
45
46
47
...
»

Summary of Contents for SureSine 1000 W



































































Reviews:

No comments

Related manuals for SureSine 1000 W

Brand: Peachtree Audio Pages: 56

Brand: Avermedia Pages: 38

Brand: Xantech Pages: 2

Mega 100 Classic

Brand: Ellumiglow Pages: 4

Brand: Xnexus Pages: 20

Brand: B PLUS TV Pages: 10

Brand: Eleris Pages: 184

IRIS BLUE 3 SQ727 Series

Brand: SALUPO Pages: 28

Multi-Decoder MD-2

Brand: tams elektronik Pages: 40

Brand: GUSTARD Pages: 22

Brand: SolaX Power Pages: 60

SUNNY BOY STORAGE 2.5

Brand: SMA Pages: 110

Brand: SMA Pages: 90

Brand: Unicont SPb Pages: 21

B-HDMI-ASI-IP-4CH

Brand: Questtel Pages: 28

Brand: M2TECH Pages: 33

Brand: Kramer Pages: 61

Brand: StarTech.com Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands