background image

1.0

Important Safety Instructions

ProStar MPPT Operator’s Manual

7

6

• Ce contrôleur de charge ne doit être connecté qu’à 

des circuits en courant continu. Ces connexions CC sont      

identifiées par le symbole ci-dessous:

   

Le régulateur MPPT ProStar doit être installé par un        
technicien qualifié conformément aux règlements du pays 
d'installation électriques. 
Un moyen de déconnexion de tous les poteaux 
d'alimentation doit être fourni. Ceux-ci se déconnecte doit 
être intégrée dans le câblage fixe. 
Une mise à la terre permanent et fiable s'impose avec       
raccordement à la borne ProStar MPPT.
Les bornes de puissance négative ProStar MPPT sont com-
muns et doivent être mise à la terre comme les directives, les 
codes locaux, et les règlements exigent. 
Le conducteur de terre doit être protégée contre tout dé-
tachement accidentel. 

Battery Safety

              

WARNING:

 A battery can present a risk of electrical     

 

    shock or burn from large amounts of short-circuit     

 

     current, fire, or explosion from vented gases.      

              Observe proper precautions.

               

AVERTISSEMENT:

  Une batterie peut présenter a ris     

    

    que de choc électrique ou de brûlure de grandes   

 

    quantités de court-circuit curlouer, incendie ou  

                explosion de ventilé gaz.  Observer précautions            

                appropriées.

   

  

    

WARNING:

  

Risk of Explosion

.

 

    Proper disposal of batteries is required.  Do not     

 

    dispose of batteries in fire.  Refer to local 

 

 

 

     regulations or codes for requirements.

               AVERTISSEMENT:

  

Risque d'Explosion.

               Au rebut des piles est nécessaire. Ne pas jeter les piles   

     

    dans le feu. Se référer aux réglementations locales ou    

   

    des codes pour les exigences.

               

CAUTION:

  When replacing batteries, use properly 

 

    specified number, sizes, types, and ratings based on 

               application and system design.

                  

PRUDENCE:  

Lorsque le remplacement des piles,  

 

 

     utilisez correctement nombre spécifié, tailles, types et  

 

      les évaluations basées sur conception de système et  

 

      d'application.

              

CAUTION:

  Do not open or mutilate batteries.               

 

   Released electrolyte is harmful to skin, and may be  

 

    toxic.

                 

PRUDENCE:  

Ne pas ouvrir ou mutiler les piles. 

  

    L'électrolyte est nocif pour la peau et peut être 

   

    toxique.

•  Servicing of batteries should be performed, or supervised, 

by personnel knowledgeable about batteries, and the

     

proper safety precautions. 

•   Be very careful when working with large lead-acid                   

batteries. Wear eye protection and have fresh water             

available in case there is contact with the battery acid.

•   Remove watches, rings, jewelry and other metal objects 

before working with batteries.

•  Wear rubber gloves and boots
•   Use tools with insulated handles and avoid placing tools 

or metal objects on top of batteries.

•  Disconnect charging source prior to connecting or        

dis

c

onnecting battery terminals.

•  Determine if battery is inadvertently grounded.  If so, 

remove the source of contact with ground.  Contact with 

any part of a grounded battery can result in electrical 

shock.  The likelihood of such a shock can be reduced 

Summary of Contents for PS-MPPT-25












































Reviews: