Morgana DigiBook 450 Instruction Manual Download Page 33

Page: 33 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

10.1

FUNDAMENTALS

Pay Attention during the glue

loading because of the high tem-

perature, as indicated by the la-

bel, and use protective systems

such as gloves.

When you operate with PUR

glue or with glue that is harmful

to health, you have to adopt all

the safety systems to handle

these kind of substances, espe-

cially when you open the glue

tank or when you replace the

glue or you do the cleaning pro-

cedure for the nozzle and the

premelter.

The tank has to be added with

the same type and model of glue.

You can use a different kind of

glue only when the system is

completely empty and cleaned

by using the Blue-Cleaner.

Drain as much as possible the glue that

you want to replace.

Enter in the tank a quantity of about

500g of Blue-Cleaner and make it pro-

trude from the main slot and the channel

of the glue; if at the end of this cleaning

cycle you are not sure that from the

valve 100% Blue-Cleaner exits, repeat

the operation.

Never open the tanks when they

are cold.

Possibility to break the seal gasket. In

addition to that the air humidity will en-

ter into the tank and will be trapped

causing premature ageing of the glue

(curing) with likely obstructions and

need of maintenance.

The machine can’t stay with the
glue tank opened more than 10

minutes if there is PUR glue in-

side.

The glue in contact with moist air modi-

fies her composition, damaging the ma-

chine.




MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands