Morgana DigiBook 450 Instruction Manual Download Page 27

Page: 27 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

POSITIONING AND WORKSPACES

Positioning:

The Perfect Binder must be positioned so as to have a clear space around of at least 31in, and

around the work area at least 59.055in.

The room where the machine is installed must be properly ventilated with air change as required by

law.

Aree di lavoro

Glue Inspection Area

Glue loading area. The operator accesses to this area to load the glue

on the machine.

Access area for service, to reach the electrical and pneumatic panel.

Transit Area

Transit area from workplace to glue loading area.

Work Area for the Opera-

tor

Working area for the operator for normal use of the machine.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands