background image

21

PROBLEM 

CAUSE

ACTION

Even though temp. 
adjusting knob is 
turned to“HOT” 
Position, heated 
water is not hot 
enough due to too 
high a water flow rate.

Water regulator is faulty. 
Faulty diaphragm in 
water control body 
assembly. 
Incorrect water control 
assembly fitted. 
Hot and cold water pipes crossed. 

Inspect and clean. 
Replace with new one. 

Replace with correct type. 

Check, re-connect correctly. 

Even though temp. 
adjusting knob is 
turned to “WARM” 
position, heated 
water is too hot due 
to a low water flow rate. 

Water regulator is faulty. 
Water pressure is insufficient. 

Water filter is clogged. 
Incorrect water control 
assembly fitted. 
Heat exchanger restriction 
(damage or limescale)

Inspect and replace it. 
Check water pressure at inlet to 
heater. Check for blockages in 
supply line or hot pipes and taps. 
If using a pump, check pump for faults. 
Clean. 
Replace with correct type. 

Replace or descale. 

Same as the above 
conditions due to 
long flame.

Too much volume of gas flow/ 
excessive gas pressure. 

Check gas pressure at the heater 
and adjust regulator within the 
correct range.

Main burner and 
pilot flame goes out 
during operation. 

Combustion spillage safety device
has activated.

None or insufficient ventilation fitted.

Blocked ventilation

Insufficient gas pressure.

Check flue for correct fitting, blockages
or any damage to flue pipe or terminal.
Check for spillage due to the effects of any

fans or adverse weather conditions.

Check the ventilation, referring to the 
appropriate standard.

Unblock ventilation, (advise the importance

of ventilation).

Check operating pressure’s at the 
burner and inlet pressure test points. Check 
the whole gas supply line for blockages

including the gas filter on the heater.

Check the gas regulator.

Main burner only 
goes out during 
operation.

Gas pressure (flow rate) is 
insufficient. 

Gas supply line is too small in 
diameter. (Insufficient gas 
supply). 
Partly blocked main burner 
injectors. 
Low water pressure and 
reduced flow rate due to other 
cold water outlets in use at 
same time as heater. 
Water filter blocked. 
Diaphragm faulty. 

Check gas cylinder regulator for 
faults and the supply pipe for 
blockages. 
Enlarge the gas supply pipe. 

Clean them. 

Check water pressure at inlet with 
water heater in operation. 
Plumbing modifications may be 
necessary to installation. 
Clean or replace. 
Replace diaphragm. 

Summary of Contents for D-61B























Reviews: