72 20 00, 72 20 01,
72 20 02, 72 20 03,
72 20 04, 72 20 05
ASSEMBLY INSTRUCTIONS
General
MORA TEMP DUO - TWO MIXERS IN ONE!
• MoraTemp Duo is a combination of a standard kitchen or wash basin mixer and
a sensor controlled tap. Using the lever the Mora Temp Duo works exactly as
any other ordinary mixer. But with the sensor function you get a non contact
function by holding your hands in front of the sensor eyes.
• When installing MoraTemp Duo in rooms where there is a periodic risk of
freezing, the fittings must be drained of water, otherwise there is a risk of the
tap being damaged through freezing.
• The control box must not be washed by high-pressure jet cleaning.
• The sensor part of the tap is fitted with automatic shut off after 24 seconds of
use (adjustable up to 48 sec). In order for the tap to start again the ”obstacle”
or your hands must be removed from in front of the sensor eyes and then moved
back again. This is a safety feature to prevent flooding if an object were to be
placed in front of the sensor eyes.
• Before connection is made, the incoming water pipes must be flushed.
NOTE:
If the red indication lamp is flashing or lights without the tap being used,
the battery voltage is too low, and the batteries must be replaced.
When the batteries have been removed and then replaced, the
RESET button on the circuit board must always be pressed in for a brief moment
to reset the electronics.
Spent products can always be sent to MORA ARMATUR AB
for recycling.
Assembly
1. Place the mixer in the hole, rec. hole dim 35mm (max 37mm - min 32mm),
and attach using the support washer and nut.
2. Remove the control cover, pull out the circuit board and make the neces-
sary changes to flush time and sensor distance. (see diagram A). Mount
the batteries, attach the sensor cable (the cable between the sensor eyes
and control box) on the circuit board, press the RESET button on the circuit
board and put back the cover. On AC operation: select AC instead of DC on
the circuit board, reset the transformer to 12V operation. Connect to circuit
board. Press RESET.
3. Connect the valve block to the mixer’s connection pipe (remember the sup-
port sleeves in the connection pipe) and to incoming hot and cold water. If the
mixer has an outlet for connecting a dishwasher, connect the dishwasher’s
connection hose to the mixer’s outlet pipe.
4. Assemble the solenoid valve with the ball valve in the control box. Then attach
the ball valve to the valve plate. Do not forget the filter/packing. If there is a
limited space against the drain trap, the enclosed elbow can be attached in
between to angle the control box 90° out of line.
5. Then fit the connection hose between the outlet on the solenoid valve and the
mixer’s connection for incoming hot water.
6. The mixer valve built into the valve block only supplies the tap with water
during sensor operation. This is set to give hot water on delivery; the exact
temperature and flow can be adjusted using the adjuster screw (see diagram
B).
NOTE:
If only cold water is required (100 %) from the tap during sensor operation,
the accompanying cold water plug must be fitted (see diagram C).
7. Turn on the water.
8. Test the activation distance. If the activation radius of the sensor is too
short/long, this can be adjusted using switch no. 6 (rough adjustment) and
the adjuster screw (fine adjustment), see diagram A.
NOTE:
Be careful - only small adjustments to the screw are needed to change
the activation distance.
9. Check that the after flush time and the maximum flush time are satisfactory,
otherwise adjust these on the circuit board in the control box.
Hot water in
Cold water in
Valve block
Connection
hose for
mixed water
Control box with solenoid valve
Sensor eyes
Lever
Indication lamp
Supporting
sleeves
Dirt filter with
gasket
Supporting
sleeves
NOTE: Requires Cu-pipe Ø 12x1
Ball valve
Mora Armatur AB
Box 440
SE-792 27 MORA
SWEDEN
www.moraarmatur.se
INSTRUCTION
1
Mora Temp Duo
07.04. MA nr 1001032