background image

Step 3:   

Remove the trim from the bottom 

of the door as shown.

Step 4:   

Remove the other side, as 

shown in Steps 1 - 3.

Removing the door trim:

Follow the steps below to remove, or install the 

R320* / R420*

 

fireplace door trim. 

Step 1:   

Grasp the trim on either side of the 

door with the tips of your fingers. 

(Both sides Typ.) 

Pull firmly to re

-

lease the trim from the internal 

door magnets.

Step 2:   

Then, pull the trim from the top of 

the door, as shown.

Removing the door:

Follow the steps to remove, or install the 

R320*/R420* 

fireplace door.

 

Reinstalling the door:

Follow the four previous steps to re-install the R-Series 

fireplace door.

Step 1:  

Remove glass suction cups from box and place on Glass door. (The 

tool may not be exactly as shown).

 

Step 2:  

Place the suction cups on the glass door, spaced evenly. (

Ensure 

they are firmly attached, and secured.)

Step 3:  

Lifting the glass panel. 

Hold the Tools firmly and lift the glass panel up and out of the lower 

track (Into the upper track). Tilt the lower edge of the door panel 
outwards.

Step 4:   

Ensure the top edge of the glass is fully removed from the upper outer 

track,  and Tilt / Lift away Cautiously from the fireplace. Store in a safe 

location until time to replace.

Section 8: Removing & Installing the Door

R320 & R420  Power Vent Indoor Gas Fireplace

Page 28

XG0770 - 100614

Installation

Summary of Contents for R320











































Reviews: