Montigo H38DF PRC Installation & Maintenance Manual Download Page 18

Page: 18 / 44

H*38DF PRC Panorama Indoor Gas Fireplace

Page 18

XG0211 - 151126

Installation

Note:

Images are shown without screens for clarity purposes.

However, your fireplace should not be operated without proper

installation of screens.

Section 3-3-3: Heat Shields

Installing a Wall Mounted RHS8 Heat shield

The RHS8 Heat shield

CANNOT

be used when the Termination is

WITHIN

36" Min. horizontal and 60" Min. vertical

from the

fireplace, or directly off the rear of the fireplace, as shown

figure

16a

. The RHS101 Heat Shield (

Figure 17 and 17a

)

MUST

used within the noted dimensions.
To install the RHS8, frame an opening in combustible construction,

Figure 16

below. Slide the Heat shield in place over the vent pipe

which attaches to the fireplace. After the fireplace and vent pipe

has been installed, clearances should match the dimensions in

Figure 16

Figure 17. RHS101 Installation. (Install by sliding Outer Section over vent

pipe where it passes through the combustible construction.

Figure 17a. Heat Shield. After sliding the outer section in place.

Termination

Drywall / sheetrock
RHS101 Heat Shield, inner Section

RHS101 Heat Shield

Outer Section

Installing a Wall Mounted RHS101 Heat shield.

The RHS101 Heat shield

MUST

be used where the RHS8 Termination

(

Figure 16 and 16a

)

CANNOT

be used.

Use the RHS101

where any of the dimensions are within the parameters
shown,

figure 16a.

To install the RHS101, Slide the Inner Section over the vent pipe that

will connect to the fireplace. Then fasten the vent pipe to the back

of the fireplace with a minimum of three sheet metal screws. From

the outside slide the RHS101 outer section on see

Figure 17

. To

complete the installation fasten the Heat Shield Outer Section &

Termination frame to the structure

Figure 17a.

Combustible

framing

Termination

Drywall / sheetrock
RHS101 Heat Shield, inner Section

RHS101 Heat Shield

Outer Section

Vent pipe, from fireplace

RHS8 Heat Shield

1” Min. Both sides Typical

1” Min.

Combustible Framing

Figure 17b.

RHS101 Installation.

Outer Shield 10 1/4”

3/8” Min. Both sides Typical

3/8” Min.

3/8” Min .

Combustible Framing

12” x 12”

Inner Shield 9 3/8”

Figure 16.

RHS8 Installation. (Install by sliding over vent pipe where it

passes through the combustible construction).

Figure 16a.

RHS8 Installation. (Minimum requirements).

RHS8 Heat

Shield

36” Min

60” Min.

Summary of Contents for H38DF PRC













































Search results

Summary of Contents for H38DF PRC

Reviews:

Related manuals for H38DF PRC

Brands by name

Popular brands

Montigo H38DF PRC, Installation & Maintenance Manual

Search results

Summary of Contents for H38DF PRC

Reviews:

Related manuals for H38DF PRC

Brands by name

Popular brands