Page 33
XG0219 - 170829
Operation
Remote (RXM5010VO)
Figure 81
Remote
Figure 82
Remote Receiver
Installation
Protection from extreme heat is very important. The remote receiver
should be kept away from temperatures exceeding 130ºF. Extreme
heat can cause damage, which is not covered under warranty.
• Before installation, make sure you turn the slide switch to OFF. After
installation, make sure you turn the slide switch to REMOTE.
• The remote receiver can be placed close to the electrical control
box.
Receiver
When plugged into a standard 110-120 VAC receptacle, the remote
receiver operates on commands from the transmitter or from the slide
switch on the face of the receiver.
• ON: will manually turn on the fireplace.
• REMOTE: will allow use of handheld transmitter. If the system does
not respond to the transmitter on initial use, check the battery
positions in the remote. If that does not work, see the SECURITY
CODE section.
• OFF: will disable the remote receiver.
• It is suggested that the slide switch be placed in the OFF position if
you will be away from your home for an extended period of time.
___________________________________________________________________________________________________________
REV 5/27/11 Page 2 of 5
Skytech 5010
SETTING
0
F /
0
C SCALE
The factory setting for temperature is
0
F
. To change this setting to
0
C
, first press and
hold the ON button and the FLAME ICON on the transmitter LCD screen at the same time
for (5) seconds. Follow this same procedure to change from
0
C back to
0
F
.
CHILDPROOF “LOCK-OUT”
This remote control includes a CHILDPROOF “LOCK-OUT” feature that allows the user to
“LOCK-OUT” operation of the appliance from the TRANSMITTER when it is in the “LOCK OUT” mode.
SETTING “LOCK-OUT”
1.
To activate the “LOCK-OUT” feature, press and hold the ON and OFF icons on the LCD
screen together, for 5 seconds. The lock icon will appear on the LCD screen.
2.
To disengage the “LOCK-OUT”, press and hold the ON and OFF icons on the LCD screen
together, for 5 seconds. The lock icon will disappear on the LCD screen and the system
will return to its normal operating condition.
NOTE: If the appliance is already operating in the ON mode engaging the “LOCK-OUT”
will not cancel the operating MODE. Engaging the “LOCK-OUT” prevents only the manual
operation of the TRANSMITTER
RECEIVER
When plugged into a standard 110-120 VAC receptacle, the remote receiver
operates on commands from the transmitter or from the slide switch on the top
of the receiver (This switch is to be used during a power outage to operate the
appliance manually). The remote receiver is manufactured with a “dry contact”
relay in its circuitry that operates like an on/off switch, however, no power or
current passes from the 110-120 VAC input side to the wires leading from the
output side of the remote receiver.
This 5010 remote control system can be used in simplified installations
to control a Millivolt gas valve without any additional relays or components.
OFF
ON
OFF
ON
To 120VAC input
Slide
Switch
OFF
REMOTE
ON
LEARN
VALVE
ANTENNA
REMOTE RECEIVER
Dry Contact
(2) 1/4” female
Connectors
The remote operates on 4-AAA batteries that are included with this
kit. Install the AAA Batteries supplied with the unit into the battery
compartment. It is recommended to use ALKALINE batteries with this
product. Be sure the batteries are installed with the (+) and (-) ends
facing in the correct direction.
When the batteries are installed, the temperature indicator should
have a value and the ON and OFF buttons should appear on the
screen. If they do not appear, check the orientation of the batteries
and change if necessary.
Note: Due to the sensitive temperature-monitoring components in the
transmitter, it may be necessary to allow the remote to stabilize to
room temperature before accurate room temperatures are displayed
on the screen. If the remote is activated from a severe cold condition,
it can take up to fifteen minutes for accurate temperature readings to
appear.
___________________________________________________________________________________________________________
REV 5/27/11 Page 1 of 5
Skytech 5010
Model: 5010
INSTALLATION AND OPERATING INSTRUCTIONS
INTRODUCTION
This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas
heating appliances. The system can be operated manually from the transmitter. The system operates on radio frequencies (RF) within
a 20-foot range using non-directional signals. The system operates one of 1,048,576 security codes that are programmed into the
transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.
The transmitter operates on 4 AAA-size 1.5V batteries. It is recommended that
ALKALINE batteries always be used for longer battery life and maximum operational
performance.
IMPORTANT
: New or fully charged batteries are essential for proper
operation of the multi-function transmitter. Insert 4 AAA-size 1.5 V batteries into the
battery compartment on the back of the transmitter, positioning the (+) and (-) ends of the
batteries as indicated on the casing. When the batteries are inserted, the screen at right
(with similar numbers) will display.
Note:
On initial start up if a LOW battery icon appears on
the screen, check the position of the batteries.
Note:
Due to the sensitive temperature-monitoring
components in the transmitter, it may be necessary to
allow the transmitter to stabilize to room temperature
before accurate room temperatures are displayed on
the screen. If the transmitter is activated from a
severe cold condition, it can take up to fifteen minutes
for accurate temperature readings to appear.
1.
BATTERY ICON
- Battery power is low. Replace batteries within two weeks.
2.
ON-
Indicates the appliance is ON – Flame Icon
3.
OFF
- Indicates the appliance is OFF – NO Flame Icon
4.
FLAME
– Indicates burner/valve in operation.
5.
ROOM
– Indicates CURRENT room temperature.
6.
0
F
indicates degrees Fahrenheit (º
C
indicates degrees Celsius).
7.
LOCK – Child lock out.
8.
RF SIGNAL ICON
–Appears when the RF signal is being transmitted.
OPERATION FUNCTIONS
1.
Touch anyplace on the screen and the screens blue back light will light up and stay on for (5)
seconds.
2.
Touch the ON button on the LCD screen front of the transmitter to turn the appliance ON.
3.
Touch the OFF button on the LCD screen front of the transmitter to turn the appliance OFF.
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT
ATTEMPT TO INSTALL OR OPERATE
OFF
BATTERY
COMPARTMENT
BACK
FRONT
ON
OFF
ON
OFF
ON
1
8
4
2
3
7
6
5
OFF
ON
spade
BATTERY
COMPARTMENT
REMOTE RECEIVER
ANTENNA
LEARN
VALVE
TO 120VAC INPUT
SLIDE
SWITCH
OFF
REMOTE
ON
DRY CONTACT
(2) 1/4" SPADE
CONNECTORS
