Monte Carlo Fan Company 5VYR56XXD Series Owner'S Manual Download Page 4

Lift Canopy to ceiling aligning the key hole slots

with the screws on the bottom of the Mounting

bracket.  Rotate the canopy Counter Clockwise

to lock in place.  Tighten the screws to secure

the Canopy.  See inset for Keyhole shape

24

Attach blades to blade arms with

screws and washers supplied. Repeat

for all 5 blades.

30

Re-install safety bar removed in step

3 by placing safety bar on screws,

sliding into place, and tightening the

2 screws.

20

Make wire connections to power source using

wire nuts provided.  Make sure that no filiments

are outside of the wire nut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on

the other side of the outlet box.

23

Install 4 x 25 watt candelabra bulbs.

26

Install assembled ornate glass cover

and glass to fan body by twisting in

direction of arrow to hold in place.

28

Tighten all 3 screws securely loos-

ened in step 25.

29

Loosen 2 screws with key hole slots

and remove 1 screw.

25

Place glass into ornate glass cover.

27

Install remote receiver by sliding into

opening in the Mounting bracket.  Make

sure that the dip switches on the

Transmitter and the Receiver are set to

the same position.  

21

Fan and light kit combinations over 70 lbs, in

both flush and downrod mode the safety cable

must be installed into the house structure

beams using the 3” lag screws,washers, and

lock washers. provided.  Make sure that when

the safety cable is fully extended the lead wires

are longer than the cable and no stress is

placed on the lead wires. 

19

Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

washer

white

black

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Orange from fan to Orange from remote

marked Light/up. Blue from fan to blue from

remote marked down light. Black from fan to

Black from remote marked L. White from

house to white from remote marked AC N .

Black from house to Black from remote

marked AC L. Connect all green ground wires

to Ground wire from House.

orange

blue

Green

white

black

House

Fan

22

fuses

Summary of Contents for 5VYR56XXD Series








Reviews: