Monte Carlo Fan Company 4LMR56 D Series Owner'S Manual And Installation Manual Download Page 8

8

© 2020 Monte Carlo Fan Collections

2/2020

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO 

CONDITIONS. (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT 

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

The receiver provides the following protective functions

Lock protection- The DC motor has a build-in safety feature 

against blade obstruction during operation. If something 

obstructs the fan blades, the motor will stop operation after 

about 20 seconds of interruption. Please remove obstacles 

and reset it by turning the power off, and turn it back.  

Over 40W protection- When the receiver detects motor 

power consumption which is greater than 40W, the fan RPM 

will be lowered to protect it from overloading. 

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous 

setting at factory. Make Remote control setting (learn function) and your fan will be ready for use.  

2.

 

If fan or light isn’t working, reset power (turn the power off then turn the power back) and redo the remote setting.

3. It is not available to separately operate the remote setting for more than one fan in the same room (in the area where remote 

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each 

fan and turn power off for the fan while you are making learn function for other fan) is required if you want to separately control 

more than one fan in same room.

4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it turns. It is a normal 

performance of this fan and it will take for few seconds to run this operation.     

Install Transmitter wall mount cradle with 2 screws provided.

Useful tips:
Take remote transmitter up by pushing it at lower area of the 

transmitter.

The remote transmitter can be held on magnetic metal 

materials by a magnet built in the transmitter.  

  

Wall mount cradle

Summary of Contents for 4LMR56 D Series











Reviews: