Monoprice MONOLITH 7 User Manual Download | Manualshive

Page: 12 / 14

background image

12

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with any
questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come online
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website www.monoprice.com
during regular business hours, 7 days a week. You can also get assistance through email by
sending a message to [email protected]

SPECIFICATIONS

Model

14566

Number of Channels

7

EIA 1kHz Output Power at 8 Ohms*

250 watts

EIA 1kHz Output Power at 4 Ohms*

375 watts

FTC Full Bandwidth Output Power
at 8 Ohms**

200 watts

FTC Full Bandwidth Output Power
at 4 Ohms**

300 watts

Input Sensitivity for Full Rated Power

1.6 Volts

Frequency Response at Rated Output 20Hz ~ 20kHz ±0.1dB
Phase Response

+5 to -15 degrees from 20Hz to 20kHz at 1 watt

Signal-to-Noise Ratio "A-Weighted"

Greater than 120dB below rated FTC Full
Bandwidth Power

«
...
10
11
12
13
14
»

Summary of Contents for MONOLITH 7















Reviews:

No comments

Related manuals for MONOLITH 7

Brand: NAD Pages: 2

Brand: PARK AUDIO Pages: 23

Sound Wave 115S

Brand: Ibanez Pages: 2

Brand: NAD Pages: 2

belles Soloist 3

Brand: Power Modules Pages: 7

Brand: Altinex Pages: 10

Brand: Texas Instruments Pages: 25

Brand: Eagletone Pages: 3

Brand: Teac Pages: 48

Brand: Saluki Pages: 85

Custom Reverb 36WE Georg Wadenius Signature

Brand: Olsson Pages: 8

Brand: B52 Pages: 31

Brand: Banner Pages: 19

Brand: Harman Kardon Pages: 28

Brand: Forney Pages: 18

Brand: McIntosh Pages: 20

Brand: Fezz Audio Pages: 12

Brand: Chiayo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands