background image

SAFETY WARNINGS AND GUIDELINES 

Please read this entire manual before using this device, paying extra attention to these 
safety warnings and guidelines. Please keep this manual in a safe place for future reference. 

 

This device is intended for indoor use only. 

 

Do not expose this device to water or moisture of any kind. Do not place drinks or 
other containers with moisture on or near the device. If moisture does get in or on 
the device, immediately unplug it from the power outlet and allow it to fully dry 
before reapplying power. 

 

Do not touch the device, the power cord, or any other connected cables with wet 
hands. 

 

Do not expose this device to excessive vibration. 

 

Do not subject the product to extreme force, shock, or fluctuations in temperature 
or humidity. 

 

Do not expose this device to excessively high temperatures. Do not place it in, on, 
or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in 
direct sunlight. 

 

Prior to operation, check the unit and power cord for physical damage. Do not use if 
physical damage has occurred. 

 

Before plugging the unit into a power outlet, ensure that the outlet provides the 
same type and level of power required by the device. 

 

Unplug this device from the power source when not in use. 

 

Take care to prevent damage to the power cord. Do not allow it to become 
crimped, pinched, walked on, or become tangled with other cords. Ensure that the 
power cord does not present a tripping hazard. 

 

Never unplug the unit by pulling on the power cord. Always grasp the connector 
head or adapter body. 

 

Ensure that power is turned off and disconnected before making any electrical 
connections. 

Summary of Contents for Blackbird 39665
























Reviews: