Monoprice 612790 User Manual Download Page 10

10 

REGULATORY COMPLIANCE 

Notice for FCC 

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following 
two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation. 

Modifying the equ

ipment without Monoprice’s authorization may result in the equipment 

no longer complying with FCC requirements for Class A digital devices. In that event, 
your right to use the equipment may be limited by FCC regulations, and you may be 
required to correct any interference to radio or television communications at your own 
expense. 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a commercial installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area is likely to cause 
harmful interference, in which case the user will be required to correct the interference 
at his own expense. 

 

Notice for Industry Canada 

This Class A digital apparatus complies with Canadian ICES-003. 

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. 

 

EU Conformity with applicable directives 

 

This equipment complies with the essential requirements listed below: 

  EMC Directive 2004/108/EC 

  Low Voltage Directive 2006/95/EC 

  RoHS Directive 2011/65/EU 

  WEEE Directive 2011/65/EU 

Summary of Contents for 612790











Reviews: