background image

SAFETY WARNINGS AND GUIDELINES 

Please read this manual thoroughly, paying extra attention to these safety warnings and 
guidelines. Keep this manual in a safe place for future reference. 
 

Installation and Operation 

 

This product should only be installed by a qualified structural contractor. Failure to 
follow proper structural code in regard to hanging equipment could result in serious 
injury or death. 

 

The ceiling or wall structure to which this projector screen will be attached must 
have a minimum load bearing capacity four times the total weight of the screen. 

 

Frequently inspect the installation for imbalance and signs of wear or damage to 
cables. Do not use if repair or adjustment is needed. 

 

Do not stand beneath this product while it is in operation. 

 

Prior to operation, ensure that the sticker on the housing and underbar is removed. 

 

General 

 

This device is intended for indoor use only. 

 

Do not expose this device to water or moisture of any kind. If water does get in or 
on the device, unplug it from its power source and allow it to fully dry before 
reapplying power. 

 

Do not touch the device, the power cord, or any other connected cables with wet 
hands. 

 

Do not expose this device to excessively high temperatures. Do not place it in, on, 
or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct 
sunlight. 

 

All wires and cables installed inside the ceiling must be rated for in-wall/in-ceiling 
use by the UL or a similar certification agency. An in-wall rating is sufficient for 

Summary of Contents for 30448





















Reviews: