background image

19 

AUDIO PROMPTS 

The following table lists all the audio prompts, the condition they represent, and the 
corrective action to take, if applicable. 

Condition/Action 

Audio Prompt 

The Home button has been pressed 

"Please wait" 

The battery level is low 

"Please charge" 

When charging is started 

"Start charging" 

When charging is complete 

"Charging finish" 

The power switch is in the off position 
during charging 

"Please turn on the power switch" 

The vacuum is lifted or is on a dark 
surface 

"Please put the machine in a safe place" 

The wheels are stuck or there is an 
internal error 

"Wheel overload" 

The dust bin is not properly installed 

"Please install the dust bin" 

An internal error has occurred 

"Side brush fault" 

A button on the vacuum or remote 
control is pressed 

Short ring 

An operating error has occurred 

Short ring 

The vacuum is powered on or off 

Long ring 

The suction inlet is clogged 

"Please clean the suction inlet" 

When scheduling is confirmed 

"Scheduling confirmed" 

Scheduling mode enabled with no 
existing schedule set 

"No scheduling" 

An operating error has occurred 

"Front bumper fault" 

 
 

 

Summary of Contents for 16385




























Reviews: