background image

Installation Instructions

4

TOOLS REQUIRED

• #2 Phillips screwdriver
• Adjustable wrench

PARTS SUPPLIED

• Monogram nameplate
• Hardware for changing door swing
• Optional stainless steel toekick with screws

and spacers

• Left and right side hinge covers
• Top screw hole cover

EARTHING THE WINE CHILLER
AND BEVERAGE CENTER

The power cord of this appliance is equipped with an
earthing plug which mates with a standard earthed
wall outlet to minimize the possibility of electric
shock hazard from this appliance.

Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly earthed.

Where an unearthed wall outlet is encountered, it is
your personal responsibility and obligation to have it
replaced with a properly earthed wall outlet.

The refrigerator should
always be plugged into its
own individual electrical
outlet. This provides the
best performance and
also prevents overloading
house wiring circuits which
could cause a fire hazard from
overheated wires. Please refer
to the rating plate on the
refrigerator for the correct
voltage, wattage and frequency.
If the product plug does not
fit your outlet, the product
should be fitted with a new plug.

STEP 1   REMOVE PACKAGING

• Remove corner blocks and foam drawer stops.

• Remove all packing material, tape and protective

plastic coverings.

• Remove stainless steel toekick taped to the back

of the unit.

CAUTION:

 Small objects are a choke

hazard for children. Remove and discard any parts
not used.

STAINING WOOD DRAWER FRONTS

The drawer fronts are unfinished cherry wood.
During use, oil from hands may accumulate and
stain the wood.

• The drawer fronts may be stained and sealed to

match adjacent cabinetry. The tinted glass will
make the stained wood appear darker. A true color
match can be seen only when the door is opened.

• Apply the stain and sealer according to the

manufacturer’s instructions. To avoid unpleasant
odor, keep the door open to ventilate and allow
the stain/sealer to dry completely before using
the product.

Insure proper
earthing exists
before using

Earthing plug

Summary of Contents for ZDBG240S









Reviews: